Polyimide flex circuits with rolled-annealed copper — rated for millions of dynamic bend cycles, biocompatible on request, and available in thicknesses as low as 0.05 mm.
A flexible PCB (FPC) is a circuit built on a thin polyimide (PI) base instead of rigid FR4 — allowing it to bend, fold and flex repeatedly without trace fracture or delamination.
The key material difference is rolled-annealed (RA) copper foil. Unlike standard electrodeposited copper, RA copper has a crystalline grain structure aligned with the rolling direction — giving it the fatigue resistance to survive millions of bend cycles without work-hardening and cracking.
Beyond bending, flex circuits eliminate harnesses and board-to-board connectors — each one a potential failure point and a source of assembly variation. One continuous flex circuit replaces multiple components and the labour to install them.
Get Flex PCB Quote →
Flex bukan sekadar 'PCB yang bisa ditekuk'. Produk ini mengubah arsitektur perakitan Anda dengan cara-cara yang meningkatkan keandalan, mengurangi massa, dan memungkinkan bentuk fisik yang tidak dapat dicapai oleh papan kaku.
Board-to-board connectors in portable and wearable products fail through mechanical stress, fretting corrosion and tolerance stack-up. Replacing a connector with a flex circuit removes the failure mode entirely. In applications with millions of mating cycles (laptop hinges, wearable clasps), flex is not an option — it is the only viable solution.
connector elimination · zero fretting · lower field failure rateA properly designed flex circuit with RA copper and correctly oriented traces survives millions of dynamic bend cycles at 0.5 mm bend radius — the equivalent of 15+ years of daily use in a wristband. Standard ED copper at the same bend radius will fracture within tens of thousands of cycles.
RA copper · perpendicular trace orientation · 1M+ cycle qualifiedPolyimide base material with ENIG finish is among the most biocompatible PCB constructions available — suitable for skin-contact wearables and, with ISO 10993 material certification, for implantable medical devices. Our PI materials are compatible with ETO sterilisation and gamma radiation, enabling use across the full range of medical device applications.
ISO 10993 · ENIG skin-safe · ETO / gamma sterilisation compatibleKemampuan fleksibilitas dinamis telah dikonfirmasi melalui pengujian siklus, bukan diperkirakan berdasarkan lembar spesifikasi.
| Jumlah Lapisan | 1 – 8 layers flex / 2 – 20 rigid-flex |
| Lebar Garis Terkecil | 0,05 mm fleksibel / 0,065 mm standar |
| Radius Tekuk Minimum | 0,5 mm dinamis / 0,3 mm statis |
| Jenis Tembaga | Digulung dan Di-anneal (RA) untuk zona fleksibel |
| Bahan Dasar | Polyimide (PI) — Kapton-equivalent |
| Ketebalan Total (satu lapis) | minimal 0,05 mm |
| Permukaan Akhir | ENIG / ENEPIG (dapat disesuaikan agar biokompatibel sesuai permintaan) |
| Peringkat Siklus Fleksibel | Millions (dynamic) · 100+ (static bend) |
| Standar Pembuatan IPC | Standar PCB fleksibel IPC-6013 |
| Sterilisasi | Kompatibel dengan ETO/gamma berdasarkan permintaan |
Proses fabrikasi fleksibel menggunakan bahan dan peralatan yang berbeda dari proses pembuatan PCB kaku standar pada setiap tahapnya.
Film poliimida dipotong dan dilapisi tembaga menggunakan proses laminasi berbasis perekat atau tanpa perekat. Foil tembaga RA dipilih untuk aplikasi fleksibel dinamis.
Jalur sirkuit dibentuk melalui proses litografi UV dan diukir secara kimiawi. Lebar jalur yang sangat tipis hingga 0,05 mm pada bagian fleksibel.
Lapisan penutup PI (bukan solder mask) dipotong secara presisi dan dilaminasi pada area fleksibel, sehingga bantalan SMT tetap terbuka. Penguat direkatkan pada zona komponen.
ENIG atau ENEPIG diterapkan untuk menjamin keandalan kontak jangka panjang. Dilakukan pengujian kelistrikan 100% serta uji kualifikasi siklus lentur.
Setiap produk yang dapat ditekuk, diputar, disesuaikan bentuknya, atau dihubungkan dalam ruang 3D.
Fleks ultra-tipis untuk jam tangan pintar dan perangkat pelacak kesehatan, di mana berat papan memengaruhi kepatuhan pengguna.
Kabel Micro-flex yang mengalirkan sinyal audio, daya, dan sensor sentuh di dalam batang earbud berdiameter 5 mm.
PI fleksibel yang biokompatibel untuk implan koklea, neurostimulator, dan prostesis retina.
Pita fleksibel untuk kamera mirrorless, kamera aksi, dan gimbal drone dengan sambungan yang dapat berputar.
Joint-crossing flex circuits in collaborative robot arms — replacing harnesses that wear and fail.
Kabel fleksibel pada engsel layar laptop dan ponsel lipat dirancang untuk tahan jutaan siklus lipatan.
Sirkuit fleksibel pada kursi, kolom kemudi, dan panel pintu menggantikan rangkaian kabel yang besar dan tebal.
PI fleksibel yang ringan untuk struktur satelit yang dapat dipasang, di mana massa menjadi kendala utama.
Sirkuit fleksibel yang lulus uji AOI pada saat pengiriman mungkin tetap mengalami kegagalan setelah 50.000 siklus pembengkokan. Proses kualifikasi kami mencakup pengujian siklus dinamis dan pembedahan mikro pada zona pembengkokan untuk memastikan masa pakai kelelahan sebelum produk diluncurkan ke produksi.
Real flexible PCB challenges — solved.
Ketebalan total 0,6 mm, 200.000 siklus lentur dinamis pada engsel, lapisan ENIG yang biokompatibel, BGA 0,4 mm pada zona SoC yang kaku.
Telah lulus uji kualifikasi 200.000 siklus. Tinggi perakitan berkurang 0,4 mm dibandingkan desain konektor sebelumnya. Tidak terjadi delaminasi lapisan penutup sama sekali selama proses produksi selama 2 tahun.
Bahan sesuai standar ISO 10993, lapisan ENIG, lebar jalur 0,08 mm, kompatibel dengan sterilisasi ETO, radius tekukan statis 0,3 mm.
Biokompatibilitas telah disetujui oleh Badan Pemberi Keterangan Uni Eropa. Tidak ada kasus kegagalan dalam pemantauan pasca-implantasi selama 5 tahun yang melibatkan 800 pasien.
RA copper PI flex replacing 14-wire harness in a collaborative robot joint — rated 5 million dynamic cycles at 0.5 mm bend radius.
Uji kualifikasi siklus 5M telah lulus. Waktu perakitan kabel sambungan berkurang dari 12 menit menjadi 90 detik. Tidak ada kegagalan kabel selama 3 tahun pengoperasian robot.
Pertanyaan teknis yang paling sering diajukan oleh para insinyur sebelum memesan sirkuit fleksibel dan sirkuit fleksibel-kaku.
Our standard flex base material is polyimide (PI) film — chemically equivalent to DuPont Kapton. PI provides the thermal stability (up to 260°C), chemical resistance and mechanical compliance that flex circuits require. For skin-contact and implantable applications, we can confirm ISO 10993 biocompatibility. LCP (Liquid Crystal Polymer) substrate is available for ultra-low-profile millimetre-wave flex applications.
Our standard minimum dynamic bend radius is 0.5 mm for designs using 1 oz (35 µm) copper. Static-fold applications (bent once during assembly) can achieve 0.3 mm. For tighter radii, reduce copper weight to 0.5 oz and increase the number of flex layers to reduce per-layer strain. Our flex engineers review bend radius, trace orientation and copper weight together in the DFM review.
Solder mask is a photoimageable liquid coating — suitable for rigid PCBs where it is not subject to repeated flexing. Coverlay is a laminated PI film with adhesive — it flexes with the circuit without cracking. Flex regions must always use coverlay, not solder mask. SMT pad areas in rigid or stiffened zones can use solder mask for compatibility with standard paste printing and automated optical inspection.
Selalu tentukan tembaga rolled annealed (RA) untuk area fleksibel dinamis. Tembaga RA memiliki struktur butir kristal yang sejajar dengan arah penggulungan, sehingga memiliki ketahanan terhadap kelelahan yang memungkinkannya bertahan melalui jutaan siklus pembengkokan. Tembaga electrodeposited (ED) memiliki struktur butir kolumnar yang mengalami pengerasan akibat deformasi dengan cepat akibat pembengkokan berulang dan akan retak dalam puluhan ribu siklus pada aplikasi dinamis. Pilihan standar kami untuk semua pesanan komponen fleksibel adalah tembaga RA.
Our standard polyimide base material with ENIG finish is widely used in skin-contact wearables without special qualification. For medical device regulatory submissions requiring ISO 10993 biocompatibility documentation, we can provide third-party test reports on request. ETO and gamma sterilisation compatibility is available — specify sterilisation method at the time of enquiry.
We offer FR4 stiffeners (0.2–1.6 mm) bonded with pressure-sensitive adhesive (PSA) for room-temperature assembly, and polyimide stiffeners bonded with thermally cured adhesive for high-temperature applications. Stiffeners are used to rigidise connector termination areas, component mounting zones and through-hole pad areas. Stiffener placement and thickness are reviewed in the DFM process.
Kirimkan desain fleksibel atau spesifikasi mekanis Anda. Tim insinyur fleksibel kami akan meninjau radius lengkungan, orientasi jalur, dan desain lapisan penutup dalam waktu 8 jam.
Isi detail di bawah ini dan kami akan segera menghubungi Anda.
Kami menggunakan cookie untuk meningkatkan pengalaman Anda. Lihat kebijakan kami Kebijakan Privasi.