フレキシブルプリント基板(FPC)の製造

フレキシブルPCB
(FPC/フレキシブル回路)

Polyimide flex circuits with rolled-annealed copper — rated for millions of dynamic bend cycles, biocompatible on request, and available in thicknesses as low as 0.05 mm.

ポリイミド基板 曲げ半径 0.5 mm ダイナミック・フレックス 生体適合性ENIG
0.5mm
最小動的曲げ半径
PI
ポリイミド基板
0.05mm
最小トレース幅
M+
動的フレックスサイクル
48h
エクスプレス・プロトタイプ
フレキシブルPCBとは

曲がり、折りたたまれ、製品にぴったりとフィットする回路

A flexible PCB (FPC) is a circuit built on a thin polyimide (PI) base instead of rigid FR4 — allowing it to bend, fold and flex repeatedly without trace fracture or delamination.

The key material difference is rolled-annealed (RA) copper foil. Unlike standard electrodeposited copper, RA copper has a crystalline grain structure aligned with the rolling direction — giving it the fatigue resistance to survive millions of bend cycles without work-hardening and cracking.

Beyond bending, flex circuits eliminate harnesses and board-to-board connectors — each one a potential failure point and a source of assembly variation. One continuous flex circuit replaces multiple components and the labour to install them.

Get Flex PCB Quote →
フレキシブルPCB
PI基板 RA 銅 ダイナミック・フレックス 生体適合性ENIG カバーレイ保護
技術と特長

リジッド基板+コネクタと比較したフレキシブル基板の3つの技術的利点

Flexは、単に「曲げられるPCB」というだけのものではありません。信頼性を向上させ、質量を低減し、リジッド基板では実現できないフォームファクタを可能にするなど、アセンブリのアーキテクチャそのものを変革します。

01

Eliminate Connectors — Eliminate Failure Points

Board-to-board connectors in portable and wearable products fail through mechanical stress, fretting corrosion and tolerance stack-up. Replacing a connector with a flex circuit removes the failure mode entirely. In applications with millions of mating cycles (laptop hinges, wearable clasps), flex is not an option — it is the only viable solution.

connector elimination · zero fretting · lower field failure rate
02

0.5 mm Dynamic Bend Radius — Millions of Cycles

A properly designed flex circuit with RA copper and correctly oriented traces survives millions of dynamic bend cycles at 0.5 mm bend radius — the equivalent of 15+ years of daily use in a wristband. Standard ED copper at the same bend radius will fracture within tens of thousands of cycles.

RA copper · perpendicular trace orientation · 1M+ cycle qualified
03

生体適合性があり、人体に安全

Polyimide base material with ENIG finish is among the most biocompatible PCB constructions available — suitable for skin-contact wearables and, with ISO 10993 material certification, for implantable medical devices. Our PI materials are compatible with ETO sterilisation and gamma radiation, enabling use across the full range of medical device applications.

ISO 10993 · ENIG skin-safe · ETO / gamma sterilisation compatible
技術仕様

フルフレックスPCBの仕様

データシートからの推定ではなく、サイクル試験によって動的屈曲性能が確認されています。

加工パラメータ

層数1 – 8 layers flex / 2 – 20 rigid-flex
最小トレース幅0.05 mm フレックス / 0.065 mm 標準
最小曲げ半径0.5 mm(動的)/0.3 mm(静的)
銅タイプフレックスゾーン用 圧延焼鈍(RA)
基材Polyimide (PI) — Kapton-equivalent

性能と基準

総厚さ(単層)最小0.05 mm
表面仕上げENIG / ENEPIG(ご要望に応じて生体適合性あり)
フレックス・サイクル評価Millions (dynamic) · 100+ (static bend)
IPC構築基準IPC-6013 フレキシブルPCB規格
不妊手術ご要望に応じて、ETO/ガンマ線対応可能
製造工程

フレキシブルPCBの製造工程

フレキシブル基板の製造では、各工程において、標準的なリジッドPCBの製造とは異なる材料や金型が使用されます。

01
ステップ 01

PIラミネートの調製

ポリイミドフィルムは、接着剤を使用する方法または接着剤を使用しない方法による積層工程を経て、裁断され、銅箔が貼り付けられます。動的フレックス用途には、RA銅箔が採用されています。

02
ステップ 02

イメージング・エッチング

回路パターンは、UVリソグラフィーによって形成され、化学エッチングによって加工されます。フレキシブル部分では、0.05 mmまでの微細な配線幅を実現しています。

03
ステップ 03

カバーレイラミネート

PIカバーレイ(ソルダーマスクではない)は、フレキシブル部分に精密に裁断・ラミネートされ、SMTパッドが露出するようになっています。補強材は部品配置エリアに貼り付けられています。

04
ステップ 04

表面仕上げおよび試験

ENIGまたはENEPIGは、長寿命かつ高い接点信頼性を確保するために採用されています。100%の電気試験および屈曲サイクル試験による認定が行われています。

用途

フレキシブルPCBが、リジッドPCBでは実現できないことを実現する場面

3次元空間において、曲がる、回転する、形状を合わせる、または接続するあらゆる製品。

01

ウェアラブル端末・フィットネスバンド

基板の重量がユーザーの継続的な利用に影響を与えるスマートウォッチやヘルストラッカー向けの超薄型フレックス基板。

02

TWSイヤホン

直径5mmのイヤホンステム内部で、オーディオ、電源、タッチセンサーの配線をマイクロフレックスで配線しています。

03

医療用インプラント

人工内耳、神経刺激装置、網膜プロテーゼ向けの生体適合性PIフレックス。

04

カメラシステム

回転ジョイント付きのミラーレスカメラ、アクションカメラ、ドローンのジンバル用フレックスリボン。

05

ロボティクス

Joint-crossing flex circuits in collaborative robot arms — replacing harnesses that wear and fail.

06

ノートパソコン&折りたたみ式端末

ノートパソコンのディスプレイや折りたたみ式スマートフォンに採用されているヒンジ用フレックスケーブルは、数百万回の折りたたみサイクルに耐える仕様となっています。

07

自動車用センサー

座席の占有状況、ステアリングコラム、ドアパネルのフレキシブル回路が、かさばるワイヤーハーネスに取って代わっています。

08

衛星サブシステム

質量が主要な制約となる衛星用展開構造物向けの軽量PIフレックス。

製造・品質

屈曲サイクル試験により、フレックスの品質が確認されています。

納品時にAOI検査に合格したフレキシブル回路であっても、50,000回の曲げサイクル後に故障する可能性があります。当社の認定プロセスでは、量産開始前に疲労寿命を確認するため、動的サイクル試験および曲げ部の微細断面検査を実施しています。

  • ISO 9001:2015第三者による監査を受けた品質管理
  • IPC-6013フレキシブルPCBの認定基準
  • IPC-A-600許容基準
  • ISO 10993に準拠ご要望に応じて生体適合性試験を実施いたします

検査および試験方法

  • 100% Electrical Test — Flying Probeすべてのネット、すべてのボード
  • 100% AOI自動光学検査
  • フレックス・サイクリング・テストPer IPC-TM-650 2.4.34 — qualification lots
  • Microsection — Flex Bend Zone銅の疲労および層間剥離の点検
  • カバーレイの剥離強度IPC-TM-650 2.4.9 に基づき
  • ENIG Thickness — XRF皮膚接触用基板における均一性
  • 寸法確認外形および穴の位置
  • 滅菌対応性ご要望に応じてETO/ガンマ線処理を実施
機能の例

当社が製造したフレキシブル回路基板

Real flexible PCB challenges — solved.

Wearable · Smartwatch

6層リジッド・フレックス構造のスマートウォッチ

総厚0.6 mm、ヒンジ部で20万回の動的屈曲サイクル、生体適合性ENIG、リジッドSoCゾーン上の0.4 mm BGA。

0.6mm
厚さ
20万
フレックスサイクル
98%
ファーストパス
結果

20万サイクルの認定試験に合格しました。従来のコネクタ設計と比較して、組立高さを0.4 mm低減しました。2年間の量産期間中、カバーレイの剥離は1件も発生しませんでした。

Medical · Cochlear Implant

生体適合性インプラント用フレキシブル回路

ISO 10993準拠の材料、ENIGめっき、配線幅0.08 mm、ETO滅菌対応、静的曲げ半径0.3 mm。

0.08mm
トレース幅
0.3mm
曲げ半径
ISO10993
生体適合性
結果

EU指定機関により生体適合性が認められています。800名の患者を対象とした移植後5年間の追跡調査において、不具合は1件も発生していません。

Robotics · Joint Flex

コボット用関節ダイナミックフレックス回路

RA copper PI flex replacing 14-wire harness in a collaborative robot joint — rated 5 million dynamic cycles at 0.5 mm bend radius.

5M
フレックスサイクル
0.5mm
曲げ半径
-40°C
私の時間
結果

500万サイクルの認定試験に合格しました。接合配線のアセンブリ時間を12分から90秒に短縮しました。ロボット導入後3年間、ハーネスの不具合は1件も発生していません。

FAQ

フレキシブルPCBに関するよくある質問

フレキシブル基板やリジッドフレキシブル基板を発注する前に、エンジニアが最もよく尋ねる技術的な質問。

Our standard flex base material is polyimide (PI) film — chemically equivalent to DuPont Kapton. PI provides the thermal stability (up to 260°C), chemical resistance and mechanical compliance that flex circuits require. For skin-contact and implantable applications, we can confirm ISO 10993 biocompatibility. LCP (Liquid Crystal Polymer) substrate is available for ultra-low-profile millimetre-wave flex applications.

Our standard minimum dynamic bend radius is 0.5 mm for designs using 1 oz (35 µm) copper. Static-fold applications (bent once during assembly) can achieve 0.3 mm. For tighter radii, reduce copper weight to 0.5 oz and increase the number of flex layers to reduce per-layer strain. Our flex engineers review bend radius, trace orientation and copper weight together in the DFM review.

Solder mask is a photoimageable liquid coating — suitable for rigid PCBs where it is not subject to repeated flexing. Coverlay is a laminated PI film with adhesive — it flexes with the circuit without cracking. Flex regions must always use coverlay, not solder mask. SMT pad areas in rigid or stiffened zones can use solder mask for compatibility with standard paste printing and automated optical inspection.

動的屈曲部には、必ず圧延焼鈍(RA)銅を指定してください。RA銅は、圧延方向と一致した結晶粒構造を有しており、数百万回の曲げサイクルに耐える耐疲労性を備えています。一方、電解(ED)銅は柱状結晶粒構造を有しており、繰り返しの曲げにより急速に加工硬化が進み、動的用途では数万回のサイクル以内に破断してしまいます。当社では、すべてのフレックス製品のご注文において、デフォルトでRA銅を採用しています。

Our standard polyimide base material with ENIG finish is widely used in skin-contact wearables without special qualification. For medical device regulatory submissions requiring ISO 10993 biocompatibility documentation, we can provide third-party test reports on request. ETO and gamma sterilisation compatibility is available — specify sterilisation method at the time of enquiry.

We offer FR4 stiffeners (0.2–1.6 mm) bonded with pressure-sensitive adhesive (PSA) for room-temperature assembly, and polyimide stiffeners bonded with thermally cured adhesive for high-temperature applications. Stiffeners are used to rigidise connector termination areas, component mounting zones and through-hole pad areas. Stiffener placement and thickness are reviewed in the DFM process.

お見積りをご依頼ください

Get your flex circuit reviewed — today.

フレキシブル回路の設計図や機械的要件をお送りください。当社のフレキシブル回路エンジニアが、8時間以内に曲げ半径、配線方向、カバーレイの設計について確認いたします。

  • すべてのお問い合わせにDFMレビューが含まれます
  • NDA signed on request — standard practice
  • 8営業時間以内にご返信いたします
  • 48時間でのプロトタイプ作成が可能
  • お見積もりのご依頼に、ご契約の義務は一切ありません
フレキシブルPCBの見積もり依頼 All files encrypted · Max 80MB · DFM review included

お見積りのお申し込み

以下の詳細をご記入ください。折り返しご連絡いたします。

WhatsApp