セラミック基板の製造

セラミック基板
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
AlNの熱伝導率
350°C
最高使用温度
DPC
ダイレクトプレート銅めっきプロセス
25µm
最小トレース幅(DPC)
0CTE Δ
SiC/GaNとのミスマッチ
セラミックPCBとは

有機PCBでは物理的に性能を発揮できない用途向けの基板

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
セラミック基板
Al₂O₃ 96% / 99% AlN 170 W/m·K DPCプロセス SiCにCTEが適合 HTCC / LTCC
技術と特長

セラミックを唯一の実用的な基板たらしめる3つの技術的現実

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
技術仕様

オールセラミックPCBの仕様

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

加工パラメータ

基板材料Al₂O₃ 96% · Al₂O₃ 99% · AlN
熱伝導率24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
プロセスDPC · HTCC · LTCC
最小トレース/スペース25 µm / 25 µm (DPC process)
銅の厚さ5 µm – 300 µm (DPC)

性能と基準

動作温度-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE(AlN)4.5 ppm/°C — near-match to SiC / GaN
表面仕上げENIG · bare Cu · Electrolytic Au
基板の厚さ0.25 mm – 3.0 mm
表面粗さ(Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
製造工程

セラミック基板の製造方法

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
ステップ 01

試料の調製

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
ステップ 02

PVDシード層

Ti/Cu または Ti/Ni のシード層を物理気相蒸着(PVD/スパッタリング)により成膜し、その後の電気めっきのための均一な導電性下地を形成する。

03
ステップ 03

電解銅めっきおよび画像形成

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
ステップ 04

表面仕上げおよび検査

ENIG(電解金メッキ)が施されています。100%の光学検査、電気的試験、および剥離強度の試験を経て、DPCプロセスが完了します。

用途

セラミック基板が唯一の実用的な基板である場合

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

SiCおよびGaNパワーモジュール

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

高出力LEDアレイ

接合部温度が寿命を左右する、マルチダイLEDアレイおよびUV殺菌用途向けのアルミナセラミックス。

03

自動車用SiCインバータ

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

RF電力増幅器

熱管理と電気的絶縁を同時に必要とするRF PAモジュール向けのAlN。

05

レーザーダイオード用サブマウント

サブミクロンレベルの平坦度が求められるシングルエミッタ型およびバー型レーザーダイオード向けの高精度セラミック。

06

航空宇宙用パワーエレクトロニクス

航空電子機器用DC-DCコンバータおよび衛星用電力調整装置向けの、軽量で高効率なセラミック。

07

医療用電気外科手術

電気外科用ジェネレータの出力回路用高電圧絶縁セラミック。

08

軍事用電力システム

極限の温度条件下で動作するレーダー送受信モジュールの電力段向け、軍用規格のセラミック。

製造・品質

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015第三者による監査を受けた品質管理
  • 材料の認証Al₂O₃ and AlN substrate purity documentation
  • 熱伝導率 CoCAlNにおけるロットごとのレーザーフラッシュ測定
  • RoHS / REACHEUの有害物質規制への準拠

検査および試験方法

  • 100% Electrical Test — Flying Probeあらゆるネット、あらゆる基質
  • 100% AOI銅配線のトレースおよび寸法検査
  • 銅の剥離強度試験ロットごとのDPC-Cuセラミック界面の接着性
  • Thermal Conductivity — Laser FlashAlN基板におけるロットごとの測定
  • 表面粗さ(Ra)ダイ接着面のプロファイル測定
  • 反り・平坦度ダイアタッチの平坦度測定におけるレーザープロファイル測定
  • Thermal Cycling -55°C to +350°Cご要望に応じて電源のオン・オフ試験を実施します
  • XRFによる被膜厚さの測定ENIG/Auめっき膜厚の測定
Get Ceramic PCB Quote →
機能の例

当社が製造したセラミック基板

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

150 kW SiCインバータ用AlN基板

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
導電率
300µm
Cuの厚さ
150kW
インバータ
結果

接合部から筐体までの熱抵抗は、競合するアルミナ設計よりも22%低い。10,000回のパワーサイクル試験に合格した。顧客は前世代製品と比較して35%高い電力密度を実現した。

LED · UV-C Disinfection

500 W UV-C LED セラミックアレイ

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
LEDの電力
24W/m·K
導電率
120°C
連続
結果

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

200 W GaN PA用AlN基板

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
RF電力
50µm
RF配線
AlN
基板
結果

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

セラミック基板に関するよくある質問

DPCセラミック基板に関する技術的な質問、材料選定および熱性能について。

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

お見積りをご依頼ください

Get your ceramic substrate design reviewed — today.

熱設計要件、ダイアタッチ仕様、およびパワーサイクリングプロファイルをお送りください。当社のセラミックスエンジニアが、8時間以内に推奨材料とDPCプロセスのレビュー結果をご提示いたします。

  • すべてのお問い合わせにDFMレビューが含まれます
  • NDA signed on request — standard practice
  • 8営業時間以内にご返信いたします
  • 48時間でのプロトタイプ作成が可能
  • お見積もりのご依頼に、ご契約の義務は一切ありません
セラミック基板の見積もり依頼 All files encrypted · Max 80MB · DFM review included

お見積りのお申し込み

以下の詳細をご記入ください。折り返しご連絡いたします。

WhatsApp