Tillverkning av keramiska kretskort

Keramisk kretskort
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
AlN:s värmeledningsförmåga
350°C
Högsta driftstemperatur
DPC
Direktpläteringsprocess för koppar
25µm
Minsta spårbredd (DPC)
0CTE Δ
Mismatch jämfört med SiC/GaN
Vad är ett keramiskt kretskort?

Underlaget för tillämpningar där organiska kretskort rent fysiskt inte klarar av uppgiften

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
Keramisk kretskort
Al₂O₃ 96% / 99% AlN 170 W/m·K DPC-processen CTE-anpassad till SiC HTCC / LTCC
Teknik och fördelar – Maskens färg

Tre tekniska faktorer som gör keramik till det enda lämpliga substratet

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
Tekniska specifikationer

Specifikation för helt keramiska kretskort

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

Tillverkningsparametrar – Maskfärg

SubstratmaterialAl₂O₃ 96% · Al₂O₃ 99% · AlN
Värmeledningsförmåga24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
ProcessDPC · HTCC · LTCC
Min. Spår / Mellanslag25 µm / 25 µm (DPC process)
Kopparens tjocklek, maskens färg5 µm – 300 µm (DPC)

Prestanda och standarder – Maskens färg

Driftstemperatur-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
YtbehandlingENIG · bare Cu · Electrolytic Au
Substratets tjocklek0.25 mm – 3.0 mm
Ytjämnhet (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
Tillverkningsprocess – Maskens färg

Hur keramiska kretskort tillverkas

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
Steg 01r Maskfärg

Förberedelse av underlaget

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
Steg 02r Maskfärg

PVD-grundskikt

Ett Ti/Cu- eller Ti/Ni-grundskikt avsätts genom fysikalisk ångdeposition (PVD/sputtering) för att skapa en enhetlig, ledande bas inför den efterföljande galvaniseringen.

03
Steg 03r Maskfärg

Elektrolytisk kopparplätering och bildframställning

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
Steg 04r Maskfärg

Ytbehandling och kontroll

ENIG-beläggning, dvs. elektrolytisk guldbeläggning, appliceras. DPC-processen avslutas med 100 % optisk kontroll, elektrisk testning och provning av avdragningshållfasthet.

Ansökningar

När keramiska kretskort är det enda lämpliga substratet

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

SiC- och GaN-effektmoduler

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

Högpresterande LED-matriser

Aluminiumoxidkeramik för LED-matriser med flera dioder och UV-desinfektion, där övergångstemperaturen avgör livslängden.

03

SiC-växelriktare för fordonsindustrin

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

RF-effektförstärkare

AlN för RF-effektförstärkarmoduler som kräver både värmehantering och elektrisk isolering.

05

Underlag för laserdioder

Högprecisionskeramik för laserdioder med en emitter och stavlaserdioder som kräver en planhet på submikronnivå.

06

Kraftelektronik för flyg- och rymdindustrin

Viktbesparande keramik för DC-DC-omvandlare inom flygelektronik och strömförsörjning för satelliter.

07

Medicinsk elektrokirurgi

Högspänningsisolerad keramik för utgångskretsar i elektrokirurgiska generatorer.

08

Militära kraftsystem

Keramik av militärstandard för effektsteg i radar-T/R-moduler som används vid extrema temperaturer.

Tillverkning och kvalitet – Maskens färg

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015Kvalitetsledning som granskats av oberoende tredje part
  • MaterialcertifieringAl₂O₃ and AlN substrate purity documentation
  • Värmeledningsförmåga CoCLaserflashmätning per parti på AlN
  • RoHS / REACHEfterlevnad av EU:s bestämmelser om farliga ämnen

Inspektions- och provningsmetoder – Maskens färg

  • 100% Electrical Test — Flying ProbeAlla nät, alla underlag
  • 100 % AOIKontroll av kopparbanor och mått
  • Provning av kopparskalets hållfasthetDPC:s vidhäftning vid gränssnittet mellan koppar och keramik per sats
  • Thermal Conductivity — Laser FlashMätning per parti på AlN-substrat
  • Ytjämnhet (Ra)Profilometri på ytor för chipmontering
  • Båge och planhetLaserprofilometri för planhet vid chipmontering
  • Thermal Cycling -55°C to +350°CKvalificering för strömavbrott och återstart på begäran
  • XRF-mätning av beläggningstjocklekMätning av yttjocklek för ENIG-/Au-beläggning
Get Ceramic PCB Quote →
Exempel på funktioner: Maskfärg

Keramiska substrat som vi har tillverkat

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

AlN-substrat för 150 kW SiC-växelriktare

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
Ledningsförmåga
300µm
Kopparens tjocklek
150kW
Växelriktare
Resultat

Värmemotståndet mellan anslutning och hölje är 22 % lägre än hos konkurrerande konstruktioner i aluminiumoxid. Har klarat kvalificeringstestet med 10 000 strömcykler. Kunden uppnådde en 35 % högre effekttäthet jämfört med föregående generation.

LED · UV-C Disinfection

500 W UV-C LED-keramikmodul

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
LED-effekt
24W/m·K
Ledningsförmåga
120°C
Kontinuerlig
Resultat

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

AlN-substrat för 200 W GaN-effektförstärkare

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
RF-effekt
50µm
RF-ledning
AlN
Substrat
Resultat

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

Vanliga frågor om keramiska kretskort

Tekniska frågor om DPC-keramiska substrat, materialval och termiska egenskaper.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

Begär en offert

Get your ceramic substrate design reviewed — today.

Skicka in era krav på värmehantering, specifikationer för chipmontering och profil för strömcykler. Våra keramikingenjörer återkommer med en materialrekommendation och en granskning av DPC-processen inom 8 timmar.

  • DFM-granskning ingår i varje förfrågan
  • NDA signed on request — standard practice
  • Svar inom 8 arbetstimmar
  • Prototyp tillgänglig inom 48 timmar
  • Ingen förpliktelse krävs för att få en offert
Begär offert på keramiska kretskort All files encrypted · Max 80MB · DFM review included

Begär en offert

Fyll i uppgifterna nedan så hör vi av oss inom kort.

WhatsApp