Productie van keramische printplaten

Keramische printplaat
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
Warmtegeleidingsvermogen van AlN
350°C
Maximale bedrijfstemperatuur
DPC
Direct Plate Copper-proces
25µm
Minimale spoorbreedte (DPC)
0CTE Δ
Mismatch versus SiC / GaN
Wat is een keramische printplaat?

Het substraat voor toepassingen waarbij organische printplaten fysiek niet aan de eisen kunnen voldoen

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
Keramische printplaat
Al₂O₃ 96% / 99% AlN 170 W/m·K DPC-proces CTE-aangepast aan SiC HTCC / LTCC
Technologie en voordelen

Drie technische aspecten die keramiek tot het enige geschikte substraat maken

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
Technische specificaties

Specificaties voor volledig keramische printplaten

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

Productieparameters

SubstraatmateriaalAl₂O₃ 96% · Al₂O₃ 99% · AlN
Warmtegeleidingsvermogen24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
ProcesDPC · HTCC · LTCC
Min. Spatie / Spatie25 µm / 25 µm (DPC process)
Koperdikte5 µm – 300 µm (DPC)

Prestaties en normen

Bedrijfstemperatuur-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
OppervlakteafwerkingENIG · bare Cu · Electrolytic Au
Dikte van het substraat0.25 mm – 3.0 mm
Oppervlakteruwheid (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
Productieproces

Hoe keramische printplaten worden vervaardigd

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
Stap 01

Voorbereiding van het substraat

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
Stap 02

PVD-basislaag

Er wordt een Ti/Cu- of Ti/Ni-basislaag aangebracht door middel van fysische dampafzetting (PVD / sputteren) om een gelijkmatige, geleidende ondergrond te verkrijgen voor de daaropvolgende galvanische bewerking.

03
Stap 03

Elektrolytisch verkoperen en beeldvorming

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
Stap 04

Oppervlakteafwerking en inspectie

Er wordt een ENIG- of elektrolytische goudlaag aangebracht. Het DPC-proces wordt afgerond met een 100% optische inspectie, een elektrische test en een afpelsterktetest.

Toepassingen

Wanneer een keramische printplaat het enige geschikte substraat is

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

SiC- en GaN-vermogensmodules

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

Krachtige LED-arrays

Aluminiumoxidekeramiek voor LED-arrays met meerdere chips en UV-desinfectie, waarbij de levensduur wordt bepaald door de junctietemperatuur.

03

SiC-omvormers voor de automobielindustrie

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

RF-vermogensversterkers

AlN voor RF-vermogensversterkermodules waarbij zowel warmtebeheer als elektrische isolatie vereist zijn.

05

Submounts voor laserdiodes

Zeer nauwkeurig keramiek voor laserdioden met één emitter en staaflaserdioden waarvoor een vlakheid op submicronniveau vereist is.

06

Elektronica voor de lucht- en ruimtevaart

Gewichtsefficiënt keramiek voor DC-DC-omvormers in de luchtvaartelektronica en voor stroomverwerking in satellieten.

07

Medische elektrochirurgie

Hoogspanningsgeïsoleerd keramiek voor uitgangsschakelingen van elektrochirurgische generatoren.

08

Militaire energiesystemen

Keramiek volgens militaire specificaties voor vermogensfasen van radar-T/R-modules die bij extreme temperaturen werken.

Productie en kwaliteit

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015Door een onafhankelijke instantie gecontroleerd kwaliteitsbeheer
  • MateriaalcertificeringAl₂O₃ and AlN substrate purity documentation
  • Warmtegeleidingsvermogen CoCLaserflashmeting per partij op AlN
  • RoHS / REACHNaleving van EU-voorschriften inzake gevaarlijke stoffen

Inspectie- en testmethoden

  • 100% Electrical Test — Flying ProbeAlle netten, elk substraat
  • 100% AOIInspectie van koperen sporen en afmetingen
  • Test op de afpelsterkte van koperHechting van de DPC-Cu-keramische interface per partij
  • Thermal Conductivity — Laser FlashMetingen per lot op AlN-substraten
  • Oppervlakteruwheid (Ra)Profilometrie van oppervlakken voor chipbevestiging
  • Boog en vlakheidLaserprofilometrie voor het meten van de vlakheid van chipbevestigingen
  • Thermal Cycling -55°C to +350°CKwalificatie voor het uit- en weer inschakelen van de stroomvoorziening op aanvraag
  • XRF-laagdikteMeting van de dikte van de ENIG/Au-afwerking
Get Ceramic PCB Quote →
Voorbeelden van mogelijkheden

Keramische substraten die wij hebben vervaardigd

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

AlN-substraat voor een SiC-omvormer van 150 kW

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
Geleidbaarheid
300µm
Dikte van Cu
150kW
Omvormer
Resultaat

De thermische weerstand tussen de junctie en de behuizing ligt 22% lager dan bij concurrerende ontwerpen op basis van aluminiumoxide. Het product heeft de kwalificatietest met 10.000 vermogenscycli doorstaan. De klant heeft een 35% hogere vermogensdichtheid bereikt ten opzichte van de vorige generatie.

LED · UV-C Disinfection

500 W UV-C LED-keramische array

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
LED-vermogen
24W/m·K
Geleidbaarheid
120°C
Continu
Resultaat

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

AlN-substraat voor een GaN-vermogensversterker van 200 W

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
RF-vermogen
50µm
RF-spoor
AlN
Substraat
Resultaat

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

Veelgestelde vragen over keramische printplaten

Technische vragen over DPC-keramische substraten, materiaalkeuze en thermische prestaties.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

Vraag een offerte aan

Get your ceramic substrate design reviewed — today.

Stuur ons uw thermische vereisten, de specificaties voor de chipbevestiging en het vermogenscyclusprofiel. Onze keramische ingenieurs sturen u binnen 8 uur een materiaalaanbeveling en een beoordeling van het DPC-proces.

  • Bij elke aanvraag is een DFM-beoordeling inbegrepen
  • NDA signed on request — standard practice
  • Reactie binnen 8 werkuren
  • Prototype binnen 48 uur beschikbaar via de spoedservice
  • U hoeft zich niet te binden om een offerte aan te vragen
Vraag een offerte aan voor keramische printplaten All files encrypted · Max 80MB · DFM review included

Vraag een offerte aan

Vul hieronder de gegevens in en we nemen zo snel mogelijk contact met u op.

WhatsApp