One board replaces multiple PCBs and all the connectors between them — enabling 3D packaging, eliminating assembly failure points and fitting electronics into geometries no other board technology can achieve.
A rigid-flex PCB combines rigid FR4 sections (for component mounting and connector termination) with continuous polyimide flex regions (for routing between rigid sections) — all in a single laminated assembly.
The critical advantage over separate rigid boards connected by cables or ZIF connectors is the elimination of those connectors. Every board-to-board interface in your assembly is a potential failure point — mechanical fretting, corrosion, tolerance stack-up and mating force fatigue all degrade connector reliability. Rigid-flex removes them permanently.
For medical, aerospace and wearable applications, rigid-flex also enables 3D fold geometries — the board conforms to the internal volume of your enclosure, rather than requiring the enclosure to be designed around a flat board.
Get Rigid-Flex Quote →
Rigid-flex changes the architecture of your product — not just the PCB type.
Eén enkele rigid-flex-assemblage vervangt twee of meer starre printplaten en de ZIF- of board-to-board-connectoren daartussen. In een smartwatch betekent dit één printplaat in plaats van drie, en geen enkele kans op storingen door connectoren. In een chirurgische camera betekent dit een ononderbroken signaaltraject door de 3,5 mm-schacht van de endoscoop, zonder ook maar één connector in het signaalpad.
zero board-to-board connectors · reduced part count · lower field failure rateRigid-flex-printplaten kunnen worden gevouwen, gebogen en om interne structuren heen gewikkeld. Zowel avionica-modules, satellietsubsystemen als draagbare apparaten maken gebruik van rigid-flex om elektronica in vaste behuizingen onder te brengen, iets wat met een platte printplaat niet mogelijk is. De vouwgeometrie wordt als onderdeel van het printplaatontwerp ontworpen en niet bij benadering gerealiseerd met kabels en beugels.
3D fold geometry · mechanical integration · fits fixed enclosure volumeRemoving connectors, redundant PCB substrate layers and inter-board cables typically reduces assembly mass by 30–70% and volume by 40–60% compared to an equivalent multi-board assembly. For aerospace and wearable applications, these reductions are primary design requirements — not convenience features.
30–70% mass reduction · 40–60% volume reduction · aerospace & wearableDesign and fabrication under one roof — no design-to-fab handoff. Fold geometry, transition zone and layer stack reviewed together.
| Totaal aantal lagen | 2 – 20 layers (rigid + flex) |
| Flex-regio-lagen | 1 – 8 continuous flex layers |
| Min. buigradius | 0.5 mm dynamic · 0.3 mm static |
| Flex-koper type | Gewalst en gegloeid (RA) voor flexibele zones |
| Basismateriaal | Flexibele kern van polyimide + FR4 / Stijve laag met hoge Tg |
| Via typen | Doorvoergaten + verborgen/blinde gaten in stijve zones |
| IPC-bouwstandaard | Class 2 default · Class 3 on request |
| Flex-cyclusclassificatie | Millions dynamic · 100+ static |
| Oppervlakteafwerking | ENIG / ENEPIG / OSP |
| Dikte van de plaat (stijf) | 0.4 mm – 3.2 mm |
The most complex standard PCB construction — combining multilayer rigid and flexible processes in a single assembly.
Op de polyimidebasis wordt met RA-koper een patroon aangebracht voor de circuits in het flexibele gedeelte. Er wordt een afdeklaag gelamineerd om de flexibele sporen te beschermen, waarbij de SMT-pads vrij blijven.
FR4- of High-Tg-prepreg-lagen worden in een nauwkeurige perscyclus met meerdere lagen aangebracht op de stijve zones van de flexibele kern.
Mechanical and laser drilling creates through-holes and blind vias. Only rigid zones receive blind vias — flex regions route continuously through all layers.
Een ENIG-afwerking, een 100% e-test en een fysieke controle van de vouwvorm zorgen ervoor dat de assemblage vóór verzending voldoet aan de beoogde 3D-geometrie.
Elk product met meerdere printplaten die via kabelbomen of connectoren met elkaar zijn verbonden, komt in aanmerking voor vereenvoudiging door middel van een rigid-flex-printplaat.
Gevouwen 3D-avionica-modules waarbij het gewicht en de betrouwbaarheid van de connectoren bepalend zijn voor het welslagen van de missie.
Rigid-flex voor hartapparatuur, cochleaire implantaten en chirurgische camera’s die zich aan de lichaamsvorm moeten aanpassen.
Hinge-crossing rigid-flex replacing board-to-board connectors — reducing height and failure modes.
Rotatie in meerdere assen bij spiegelloze camera’s, actiecamera’s en 3,5 mm-endoscoopschachten.
Vluchtbesturingskaarten die in de structuur van het vliegtuigframe kunnen worden ingeklapt, waardoor het aantal aansluitingen en het gewicht worden verminderd.
Conforme assemblages voor militaire radio-, geleidings- en elektronische oorlogsvoering-systemen in vaste chassisvolumes.
Op gewichtsoptimalisatie ontworpen rigid-flex-printplaat voor de houdingsregeling van satellieten en uitklapbare sensorarrays.
Flexibiliteit bij het overschrijden van gewrichten in collaboratieve robotarmen en sensoreenheden van autonome mobiele robots.
Rigid-flex boards must satisfy both IPC-6012 (rigid) and IPC-6013 (flex) criteria simultaneously. Our transition zone microsection — included on every qualification lot — confirms the interface integrity that field reliability depends on.
Real 3D packaging challenges — solved with rigid-flex.
3 rigid zones + 2 flex regions, IPC Class 3, polyimide, fitting a 55×35×12 mm enclosure for a flight data recorder.
De DO-160-kwalificatietests voor trillingen en temperatuur zijn bij de eerste poging doorstaan. De assemblage van 3 printplaten en 2 connectoren is vervangen, waardoor het gewicht met 38% is verminderd en 2 storingsmogelijkheden bij de connectoren zijn geëlimineerd.
8-layer rigid-flex for a 3.5 mm scope — image sensor, LED driver and connection ribbon in one continuous assembly, biocompatible ENIG.
De fysieke afmetingen van het eerste exemplaar zijn bevestigd op een diameter van 3,5 mm. De door de EU aangemelde instantie heeft de regelgevingsdocumentatie bij de eerste beoordeling goedgekeurd.
6-laags rigid-flex, totale dikte 0,55 mm, 200.000 dynamische buigcycli bij het scharnier, biocompatibele ENIG-laag, 0,4 mm BGA in de SoC-zone.
De horlogekast is 0,6 mm dunner gemaakt ten opzichte van het vorige ontwerp met connectoren. Geen enkele afbladdering van de afdeklaag tijdens de productierun van twee jaar.
Technische vragen over het ontwerp en de fabricage van rigid-flex-printplaten en de engineering van overgangszones.
Traces in the flex region must run perpendicular to the bend axis — never parallel. Parallel traces in the bend zone experience pure tensile or compressive stress during bending and will fatigue and fracture. Perpendicular traces experience lateral stress, which the RA copper grain structure handles well. Our DFM review checks trace orientation in every flex region before fabrication begins.
In your Gerber/ODB++ package, include a separate layer defining the rigid and flex zones (typically called 'Flex Area' or 'Bend Region'). In your fabrication drawing, specify the bend axis, nominal bend radius, static vs dynamic flex classification, and stiffener requirements. Our DFM template provides a checklist — contact us for the latest version before starting your layout.
The flex region can have 1–8 continuous copper layers. Most wearable and medical rigid-flex designs use 2 or 4 flex layers. More layers in the flex region increase stiffness and require a larger minimum bend radius — our engineers calculate the required radius based on your copper weight and layer count during the DFM review.
Yes — blind and buried vias are available in the rigid zones. The flex region uses through-connections that continue as copper traces on the flex layers. Standard through-hole and blind/buried vias in rigid zones allow the same routing flexibility as a standard HDI rigid board. Microvias in rigid zones require additional press cycles and are quoted per design.
Dynamic flex regions are qualified to continuous bending through the specified bend radius over the specified number of cycles. We do not qualify fold angle directly — instead, the qualification is expressed as bend radius + cycle count. A 90° fold at 0.5 mm bend radius and 1 million cycles is a standard dynamic flex qualification. For other fold angles, the bend radius is the controlling parameter: smaller radius = higher stress = fewer cycles to failure.
Yes — for new rigid-flex designs, we offer a physical qualification unit fold verification service. The first-off board is folded to the nominal assembly geometry and photographed in the folded state. This confirms the board fits the intended enclosure before production quantities are released. Dimensional check reports are available on request.
Stuur ons uw assemblagetekening en schema. Onze ingenieurs op het gebied van rigid-flex-printplaten beoordelen binnen 8 uur de geometrie van uw 3D-vouw, de overgangszone en de laagopbouw.
Vul hieronder de gegevens in en we nemen zo snel mogelijk contact met u op.
We gebruiken cookies om uw ervaring te verbeteren. Zie onze Privacybeleid.