Rigid-Flex PCB Üretimi

Sert-Esnek PCB
(Sert + Esnek Kombinasyon)

One board replaces multiple PCBs and all the connectors between them — enabling 3D packaging, eliminating assembly failure points and fitting electronics into geometries no other board technology can achieve.

Sert + Esnek Kombinasyon 3 Boyutlu Ambalaj En fazla 20 katman IPC Sınıf 3 Dinamik Esneklik
20L
Maksimum birleşik katman sayısı
0.5mm
Minimum esneme yarıçapı
3D
Ambalaj geometrisi
IPC 3
Mevcut derleme: std
48h
Hızlı prototip
Rigid-Flex PCB Nedir?

Bükülebilen, katlanabilen ve bileşenlerin monte edilebildiği tek bir kart

A rigid-flex PCB combines rigid FR4 sections (for component mounting and connector termination) with continuous polyimide flex regions (for routing between rigid sections) — all in a single laminated assembly.

The critical advantage over separate rigid boards connected by cables or ZIF connectors is the elimination of those connectors. Every board-to-board interface in your assembly is a potential failure point — mechanical fretting, corrosion, tolerance stack-up and mating force fatigue all degrade connector reliability. Rigid-flex removes them permanently.

For medical, aerospace and wearable applications, rigid-flex also enables 3D fold geometries — the board conforms to the internal volume of your enclosure, rather than requiring the enclosure to be designed around a flat board.

Get Rigid-Flex Quote →
Sert-Esnek PCB
Sert + Esnek Kombinasyon Konektörün Kaldırılması 3 Boyutlu Katlama Geometrisi PI Flex Core IPC-6013
Teknoloji ve Avantajlar

Mühendislerin çoklu kart montajları yerine sert-esnek kartları tercih etmelerinin üç nedeni

Rigid-flex changes the architecture of your product — not just the PCB type.

01

Tüm Kart-Kart Bağlantı Elemanlarını Ortadan Kaldırın

Tek bir sert-esnek montaj, iki veya daha fazla sert devre kartının ve bunların arasındaki ZIF veya kart-kart konektörlerinin yerini alır. Bir akıllı saatte bu, üç kart yerine tek bir kart ve sıfır konektör arıza modu anlamına gelir. Bir cerrahi kamerada ise, sinyal yolunda tek bir konektör bile olmadan 3,5 mm’lik endoskop şaftı boyunca kesintisiz sinyal iletimi anlamına gelir.

zero board-to-board connectors · reduced part count · lower field failure rate
02

3D Packaging — The Board Fits the Enclosure

Sert-esnek kartlar katlanabilir, bükülebilir ve iç yapıların etrafına sarılabilir. Aviyonik modülleri, uydu alt sistemleri ve giyilebilir cihazlar, elektronik bileşenleri düz PCB montajlarının asla ulaşamayacağı sabit muhafaza hacimlerine sığdırmak için sert-esnek kartlardan yararlanır. Katlanma geometrisi, PCB tasarımının bir parçası olarak tasarlanır; kablolar ve braketlerle yaklaşık olarak oluşturulmaz.

3D fold geometry · mechanical integration · fits fixed enclosure volume
03

Mass and Volume Reduction — Measurable, Not Estimated

Removing connectors, redundant PCB substrate layers and inter-board cables typically reduces assembly mass by 30–70% and volume by 40–60% compared to an equivalent multi-board assembly. For aerospace and wearable applications, these reductions are primary design requirements — not convenience features.

30–70% mass reduction · 40–60% volume reduction · aerospace & wearable
Teknik Özellikler

Tam sert-esnek PCB teknik özellikleri

Design and fabrication under one roof — no design-to-fab handoff. Fold geometry, transition zone and layer stack reviewed together.

Üretim Parametreleri

Toplam Kat Sayısı2 – 20 layers (rigid + flex)
Esnek Bölge Katmanları1 – 8 continuous flex layers
Min. Esneklik Bükülme Yarıçapı0.5 mm dynamic · 0.3 mm static
Flex Bakır TipiEsnek bölgeler için Haddelenmiş Tavlanmış (RA)
Ana MalzemePolimid esnek çekirdek + FR4 / Yüksek Tg sert

Performans ve Standartlar

Türler aracılığıylaSert bölgelerde açık delik + gömülü/kör delik
IPC Üretim StandardıClass 2 default · Class 3 on request
Esnek Döngü DerecelendirmesiMillions dynamic · 100+ static
Yüzey İşlemiENIG / ENEPIG / OSP
Levha Kalınlığı (sert)0.4 mm – 3.2 mm
Üretim Süreci

Rijit-esnek PCB nasıl üretilir?

The most complex standard PCB construction — combining multilayer rigid and flexible processes in a single assembly.

01
Adım 01

Flex Core Hazırlığı

Esnek bölge devreleri için RA bakır içeren poliimid taban üzerine desen uygulanır. Esnek devre izlerini korumak amacıyla kaplama tabakası lamine edilir; bu işlem sırasında SMT pedleri açıkta kalır.

02
Adım 02

Sert Katmanlı Laminasyon

FR4 veya Yüksek Tg prepreg katmanları, hassas bir çok katmanlı presleme döngüsüyle esnek çekirdeğin sert bölgelerinin üzerine eklenir.

03
Adım 03

Delme ve Via Oluşturma

Mechanical and laser drilling creates through-holes and blind vias. Only rigid zones receive blind vias — flex regions route continuously through all layers.

04
Adım 04

Son İşlem, Test ve 3B Doğrulama

ENIG kaplama, 0 elektronik test ve fiziksel katlama-şekillendirme doğrulaması, sevkiyat öncesinde montajın amaçlanan 3B geometriye uygun olduğunu teyit eder.

Başvurular

Rigid-flex’in ambalajlama sorunlarını nasıl çözdüğü

Kablo demetleri veya konektörlerle birbirine bağlanmış birden fazla PCB içeren her ürün, sert-esnek tasarımla basitleştirilmeye uygun bir adaydır.

01

Havacılık ve Uzay Aviyonik

Kütle ve konektör güvenilirliğinin görev gereklilikleri olduğu katlanmış 3B aviyonik modülleri.

02

Tıbbi İmplantlar

Vücut geometrisine uyum sağlaması gereken kalp cihazları, koklear implantlar ve cerrahi kameralar için sert-esnek devreler.

03

Akıllı Saatler ve Giyilebilir Cihazlar

Hinge-crossing rigid-flex replacing board-to-board connectors — reducing height and failure modes.

04

Kameralar ve Endoskoplar

Aynasız kameralarda, aksiyon kameralarında ve 3,5 mm endoskop şaft tertibatlarında çok eksenli dönme.

05

İHA ve Drone Elektroniği

Uçak gövdesi yapılarına katlanarak konektör sayısını ve kütleyi azaltan uçuş kontrol kartları.

06

Askeriye ve Savunma

Sabit şasi hacimlerinde askeri telsiz, güdüm ve elektronik harp sistemleri için konformal montajlar.

07

Uydular

Uyduların konum kontrolü ve açılabilir sensör dizileri için kütle açısından optimize edilmiş sert-esnek devre.

08

Endüstriyel Robotik

İşbirlikçi robot kollarında ve otonom mobil robot sensör gruplarında eklem geçiş esnekliği.

Üretim ve Kalite

Rigid-flex quality — verified at both rigid and flex disciplines.

Rigid-flex boards must satisfy both IPC-6012 (rigid) and IPC-6013 (flex) criteria simultaneously. Our transition zone microsection — included on every qualification lot — confirms the interface integrity that field reliability depends on.

  • IPC-6013Sert-esnek PCB onay standardı
  • IPC-A-600 Sınıf 2 / 3Kabul edilebilirlik kriterleri
  • ISO 9001:2015Üçüncü taraflarca denetlenen kalite yönetimi
  • RoHS / REACHAB tehlikeli maddelerle ilgili mevzuata uygunluk

Denetim ve Test Yöntemleri

  • 100% Electrical Test — Flying ProbeTüm ağlar, her bir tahta
  • 100% AOI — All LayersOtomatik optik inceleme
  • Flex Cycling — Bend ZoneIPC-TM-650 standardının 2.4.34 maddesi uyarınca, kalifikasyon partileri hakkında
  • Microsection — Flex-to-Rigid TransitionGeçiş bölgesinin bütünlüğünün doğrulanması
  • Kaplama Soyulma MukavemetiIPC-TM-650 2.4.9'a göre
  • X-Ray — Buried Via RegistrationSert bölgelerdeki katman hizalaması
  • TDR Empedansı±5% on controlled rigid-zone lines
  • 3B Form KontrolüKalite kontrol partisinde fiziksel katlama ve uyum
Yetenek Örnekleri

Ürettiğimiz sert-esnek devre kartları

Real 3D packaging challenges — solved with rigid-flex.

Aerospace · Avionics

Folded Avionics Module — 12-Layer

3 rigid zones + 2 flex regions, IPC Class 3, polyimide, fitting a 55×35×12 mm enclosure for a flight data recorder.

12L
Katmanlar
3sert bölgeler
Yapı
IPC 3
std derle
Sonuç

DO-160 titreşim ve termal yeterlilik testlerini ilk denemede geçti. 3 adet PCB ve 2 adet konektörden oluşan grubu değiştirerek kütleyi oranında azalttı ve 2 adet konektör arıza durumunu ortadan kaldırdı.

Medical · Endoscope

3,5 mm Endoskop Kamerası Sert-Esnek

8-layer rigid-flex for a 3.5 mm scope — image sensor, LED driver and connection ribbon in one continuous assembly, biocompatible ENIG.

3.5mm
Kapsam çapı
8L R-F
Teknoloji
ISO10993
Biyouyumluluk
Sonuç

İlk üretimdeki fiziksel uygunluk, 3,5 mm çap olarak teyit edildi. AB Onaylanmış Kuruluşu, ilk incelemede mevzuata uygun belgeleri kabul etti.

Wearable · Smartwatch

Smartwatch — 0.55 mm Total Stack

6 katmanlı sert-esnek devre, toplam 0,55 mm, menteşede 200.000 dinamik esneme döngüsü, biyouyumlu ENIG, SoC bölgesinde 0,4 mm BGA.

0.55mm
Toplam kalınlık
200 bin
Esneklik döngüleri
99%
İlk geçiş
Sonuç

Saat kasası, önceki konektör tabanlı tasarıma kıyasla 0,6 mm inceltildi. 2 yıllık üretim sürecinde kaplama tabakasında hiçbir ayrışma görülmedi.

FAQ

Rigid-Flex PCB ile ilgili sık sorulan sorular

Rigid-flex tasarımı, üretimi ve geçiş bölgesi mühendisliği ile ilgili teknik sorular.

Traces in the flex region must run perpendicular to the bend axis — never parallel. Parallel traces in the bend zone experience pure tensile or compressive stress during bending and will fatigue and fracture. Perpendicular traces experience lateral stress, which the RA copper grain structure handles well. Our DFM review checks trace orientation in every flex region before fabrication begins.

In your Gerber/ODB++ package, include a separate layer defining the rigid and flex zones (typically called 'Flex Area' or 'Bend Region'). In your fabrication drawing, specify the bend axis, nominal bend radius, static vs dynamic flex classification, and stiffener requirements. Our DFM template provides a checklist — contact us for the latest version before starting your layout.

The flex region can have 1–8 continuous copper layers. Most wearable and medical rigid-flex designs use 2 or 4 flex layers. More layers in the flex region increase stiffness and require a larger minimum bend radius — our engineers calculate the required radius based on your copper weight and layer count during the DFM review.

Yes — blind and buried vias are available in the rigid zones. The flex region uses through-connections that continue as copper traces on the flex layers. Standard through-hole and blind/buried vias in rigid zones allow the same routing flexibility as a standard HDI rigid board. Microvias in rigid zones require additional press cycles and are quoted per design.

Dynamic flex regions are qualified to continuous bending through the specified bend radius over the specified number of cycles. We do not qualify fold angle directly — instead, the qualification is expressed as bend radius + cycle count. A 90° fold at 0.5 mm bend radius and 1 million cycles is a standard dynamic flex qualification. For other fold angles, the bend radius is the controlling parameter: smaller radius = higher stress = fewer cycles to failure.

Yes — for new rigid-flex designs, we offer a physical qualification unit fold verification service. The first-off board is folded to the nominal assembly geometry and photographed in the folded state. This confirms the board fits the intended enclosure before production quantities are released. Dimensional check reports are available on request.

Fiyat Teklifi Alın

Get your rigid-flex design reviewed — today.

Montaj çiziminizi ve şemanızı gönderin. Sert-esnek devre mühendislerimiz, 3 boyutlu katlama geometrisini, geçiş bölgesini ve katman dizilimini 8 saat içinde inceler.

  • Her talebe DFM incelemesi dahildir
  • NDA signed on request — standard practice
  • 8 iş saati içinde yanıt verilir
  • 48 saatlik ekspres prototip hizmeti mevcuttur
  • Fiyat teklifi almak için herhangi bir taahhüt gerekmez
Rigid-Flex PCB Teklifi Talep Et All files encrypted · Max 80MB · DFM review included

Fiyat Teklifi İsteyin

Aşağıdaki bilgileri doldurun, kısa süre içinde size geri dönüş yapacağız.

WhatsApp