리지드-플렉스 PCB 제조

리지드-플렉스 PCB
(경성 + 유연 결합형)

One board replaces multiple PCBs and all the connectors between them — enabling 3D packaging, eliminating assembly failure points and fitting electronics into geometries no other board technology can achieve.

경질 + 유연성 결합 3D 패키징 최대 20개 레이어 IPC 3등급 다이나믹 플렉스
20L
최대 레이어 수
0.5mm
최소 굽힘 반경
3D
포장 형상
IPC 3
사용 가능한 빌드: std
48h
익스프레스 프로토타입
리지드-플렉스 PCB란 무엇인가

구부러지고, 접히며, 부품을 장착할 수 있는 하나의 기판

A rigid-flex PCB combines rigid FR4 sections (for component mounting and connector termination) with continuous polyimide flex regions (for routing between rigid sections) — all in a single laminated assembly.

The critical advantage over separate rigid boards connected by cables or ZIF connectors is the elimination of those connectors. Every board-to-board interface in your assembly is a potential failure point — mechanical fretting, corrosion, tolerance stack-up and mating force fatigue all degrade connector reliability. Rigid-flex removes them permanently.

For medical, aerospace and wearable applications, rigid-flex also enables 3D fold geometries — the board conforms to the internal volume of your enclosure, rather than requiring the enclosure to be designed around a flat board.

Get Rigid-Flex Quote →
리지드-플렉스 PCB
경질 + 유연성 결합 커넥터 제거 3D 접힘 기하학 PI 플렉스 코어 IPC-6013
기술 및 장점

엔지니어들이 멀티보드 어셈블리 대신 리지드-플렉스를 선택하는 세 가지 이유

Rigid-flex changes the architecture of your product — not just the PCB type.

01

모든 기판 간 커넥터를 제거하십시오

단일 리지드-플렉스 어셈블리 하나로 두 개 이상의 리지드 기판과 이들 사이에 있는 ZIF 또는 기판 간 커넥터를 대체할 수 있습니다. 스마트워치의 경우, 이는 기판이 세 개에서 하나로 줄어들고 커넥터 관련 고장 요인이 완전히 사라진다는 것을 의미합니다. 수술용 카메라의 경우, 신호 경로에 커넥터가 하나도 없이 3.5mm 내시경 샤프트를 통해 신호가 연속적으로 전달된다는 것을 의미합니다.

zero board-to-board connectors · reduced part count · lower field failure rate
02

3D Packaging — The Board Fits the Enclosure

리지드-플렉스 기판은 접히거나 구부러지며 내부 구조물을 감싸는 형태로 제작됩니다. 항공전자 모듈, 위성 하위 시스템, 웨어러블 기기 등은 모두 리지드-플렉스를 사용하여 평면 PCB 어셈블리로는 따라올 수 없는 고정된 외형 치수 내에 전자 부품을 집적합니다. 접힘 구조는 케이블이나 브래킷으로 대략적으로 구현하는 것이 아니라, PCB 설계의 일부로 직접 설계됩니다.

3D fold geometry · mechanical integration · fits fixed enclosure volume
03

Mass and Volume Reduction — Measurable, Not Estimated

Removing connectors, redundant PCB substrate layers and inter-board cables typically reduces assembly mass by 30–70% and volume by 40–60% compared to an equivalent multi-board assembly. For aerospace and wearable applications, these reductions are primary design requirements — not convenience features.

30–70% mass reduction · 40–60% volume reduction · aerospace & wearable
기술 사양

풀 리지드-플렉스 PCB 사양

Design and fabrication under one roof — no design-to-fab handoff. Fold geometry, transition zone and layer stack reviewed together.

가공 매개변수

총 레이어 수2 – 20 layers (rigid + flex)
플렉스 영역 레이어1 – 8 continuous flex layers
최소 굽힘 반경0.5 mm dynamic · 0.3 mm static
플렉스 구리 타입굽힘 부위용 압연 어닐링(RA)
기판 재료폴리이미드 플렉스 코어 + FR4 / 고유리전이온도(Tg) 리지드

성능 및 표준

유형별리지드 영역의 스루홀 + 매립형/블라인드 홀
IPC 조립 표준Class 2 default · Class 3 on request
플렉스 사이클 등급Millions dynamic · 100+ static
표면 마감ENIG / ENEPIG / OSP
보드 두께 (경질)0.4 mm – 3.2 mm
제조 공정

리지드-플렉스 PCB의 제조 과정

The most complex standard PCB construction — combining multilayer rigid and flexible processes in a single assembly.

01
1단계

플렉스 코어 준비

RA 구리가 도포된 폴리이미드 기판에 플렉스 영역 회로 패턴을 형성합니다. 플렉스 트레이스를 보호하기 위해 커버레이를 적층하되, SMT 패드는 노출된 상태로 둡니다.

02
2단계

경질 적층 라미네이션

정밀 다중 적층 프레스 공정을 통해 플렉스 코어의 강성 영역 위에 FR4 또는 고 Tg 프리프레그 층을 적층합니다.

03
3단계

드릴링 및 비아 형성

Mechanical and laser drilling creates through-holes and blind vias. Only rigid zones receive blind vias — flex regions route continuously through all layers.

04
4단계

마무리, 테스트 및 3D 검증

ENIG 마감 처리, 100% 전자 테스트 및 물리적 접힘-형상 검증 과정을 통해 출하 전 조립품이 의도된 3D 형상에 부합하는지 확인합니다.

응용 분야

리지드-플렉스가 패키징 문제를 해결하는 분야

하네스나 커넥터로 연결된 여러 개의 PCB가 포함된 모든 제품은 리지드-플렉스 방식으로 단순화할 수 있는 대상입니다.

01

항공우주 항공전자공학

임무 수행에 있어 중량 및 커넥터 신뢰성이 필수 요건인 접이식 3D 항공전자 모듈.

02

의료용 임플란트

신체 구조에 밀착되어야 하는 심장 기기, 인공와우 이식 장치 및 수술용 카메라용 리지드-플렉스.

03

스마트워치 및 웨어러블 기기

Hinge-crossing rigid-flex replacing board-to-board connectors — reducing height and failure modes.

04

카메라 및 내시경

미러리스 카메라, 액션 카메라 및 3.5mm 내시경 샤프트 어셈블리에서의 다축 회전.

05

무인항공기(UAV) 및 드론 전자기기

기체 구조물에 접혀 들어가는 비행 제어 보드로, 커넥터 수와 중량을 줄여줍니다.

06

군사 및 국방

고정형 섀시 공간 내에 장착되는 군용 무선, 유도 및 전자전(EW) 시스템용 등각 조립체.

07

위성

위성 자세 제어 및 전개형 센서 어레이를 위한 질량 최적화 리지드-플렉스.

08

산업용 로봇

협동 로봇 팔 및 자율 주행 로봇 센서 어셈블리에서 관절 교차 굴곡.

제조 및 품질

Rigid-flex quality — verified at both rigid and flex disciplines.

Rigid-flex boards must satisfy both IPC-6012 (rigid) and IPC-6013 (flex) criteria simultaneously. Our transition zone microsection — included on every qualification lot — confirms the interface integrity that field reliability depends on.

  • IPC-6013리지드-플렉스 PCB 인증 기준
  • IPC-A-600 등급 2 / 3수용 기준
  • ISO 9001:2015제3자 감사를 거친 품질 관리
  • RoHS / REACHEU 유해 물질 규정 준수

검사 및 시험 방법

  • 100% Electrical Test — Flying Probe모든 네트, 모든 보드
  • 100% AOI — All Layers자동 광학 검사
  • Flex Cycling — Bend ZoneIPC-TM-650 2.4.34항에 따른 적격성 평가 로트
  • Microsection — Flex-to-Rigid Transition전환 영역 무결성 검증
  • 커버레이 박리 강도IPC-TM-650 2.4.9항에 따라
  • X-Ray — Buried Via Registration강성 영역에서의 레이어 정렬
  • TDR 임피던스±5% on controlled rigid-zone lines
  • 3D 형상 검사적격 로트의 물리적 접힘 및 착용감
기능 예시

당사가 제작한 리지드-플렉스 기판

Real 3D packaging challenges — solved with rigid-flex.

Aerospace · Avionics

Folded Avionics Module — 12-Layer

3 rigid zones + 2 flex regions, IPC Class 3, polyimide, fitting a 55×35×12 mm enclosure for a flight data recorder.

12L
레이어
3경직대
구조
IPC 3
std 빌드
결과

DO-160 진동 및 열 적합성 시험을 첫 시도에서 통과했습니다. 3개의 PCB와 2개의 커넥터로 구성된 어셈블리를 교체하여 질량을 38% 줄이고, 2가지 커넥터 고장 모드를 제거했습니다.

Medical · Endoscope

3.5mm 내시경 카메라 리지드-플렉스

8-layer rigid-flex for a 3.5 mm scope — image sensor, LED driver and connection ribbon in one continuous assembly, biocompatible ENIG.

3.5mm
시야 직경
8L R-F
기술
ISO10993
생체적합성
결과

초기 제작품의 물리적 적합성이 직경 3.5mm로 확인되었습니다. EU 지정 기관은 1차 검토에서 규제 관련 문서를 승인했습니다.

Wearable · Smartwatch

Smartwatch — 0.55 mm Total Stack

6층 리지드-플렉스, 총 두께 0.55 mm, 힌지 부위에서 200,000회의 동적 휨 사이클, 생체적합성 ENIG, SoC 영역에 0.4 mm BGA.

0.55mm
총 두께
20만
플렉스 사이클
99%
1차 처리
결과

이전 커넥터 기반 설계에 비해 시계 케이스 두께가 0.6mm 얇아졌습니다. 2년간의 생산 기간 동안 커버레이 박리 현상이 전혀 발생하지 않았습니다.

FAQ

리지드-플렉스 PCB에 대한 자주 묻는 질문

리지드-플렉스 설계, 제작 및 전환 영역 공학에 관한 기술적 질문.

Traces in the flex region must run perpendicular to the bend axis — never parallel. Parallel traces in the bend zone experience pure tensile or compressive stress during bending and will fatigue and fracture. Perpendicular traces experience lateral stress, which the RA copper grain structure handles well. Our DFM review checks trace orientation in every flex region before fabrication begins.

In your Gerber/ODB++ package, include a separate layer defining the rigid and flex zones (typically called 'Flex Area' or 'Bend Region'). In your fabrication drawing, specify the bend axis, nominal bend radius, static vs dynamic flex classification, and stiffener requirements. Our DFM template provides a checklist — contact us for the latest version before starting your layout.

The flex region can have 1–8 continuous copper layers. Most wearable and medical rigid-flex designs use 2 or 4 flex layers. More layers in the flex region increase stiffness and require a larger minimum bend radius — our engineers calculate the required radius based on your copper weight and layer count during the DFM review.

Yes — blind and buried vias are available in the rigid zones. The flex region uses through-connections that continue as copper traces on the flex layers. Standard through-hole and blind/buried vias in rigid zones allow the same routing flexibility as a standard HDI rigid board. Microvias in rigid zones require additional press cycles and are quoted per design.

Dynamic flex regions are qualified to continuous bending through the specified bend radius over the specified number of cycles. We do not qualify fold angle directly — instead, the qualification is expressed as bend radius + cycle count. A 90° fold at 0.5 mm bend radius and 1 million cycles is a standard dynamic flex qualification. For other fold angles, the bend radius is the controlling parameter: smaller radius = higher stress = fewer cycles to failure.

Yes — for new rigid-flex designs, we offer a physical qualification unit fold verification service. The first-off board is folded to the nominal assembly geometry and photographed in the folded state. This confirms the board fits the intended enclosure before production quantities are released. Dimensional check reports are available on request.

견적 받기

Get your rigid-flex design reviewed — today.

조립 도면과 회로도를 보내 주십시오. 당사의 리지드-플렉스 엔지니어들이 8시간 이내에 귀사의 3D 접힘 형상, 전환 구역 및 레이어 스택을 검토해 드립니다.

  • 모든 문의 시 DFM 검토가 포함됩니다
  • NDA signed on request — standard practice
  • 영업일 기준 8시간 이내 답변
  • 48시간 내 시제품 제작 가능
  • 견적 요청 시 별도의 약정이 필요하지 않습니다
리지드-플렉스 PCB 견적 요청 All files encrypted · Max 80MB · DFM review included

견적 요청하기

아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.

WhatsApp