Every single unit — not a sample — is visually inspected, dimensionally verified and cross-checked against a full history of test data before it's packaged and released. No board leaves without a documented pass.
상류 단계의 테스트에서는 전기적 결함을 발견합니다. 최종 검사 단계에서는 그 외의 모든 문제가 발견됩니다. 마우스를 올려놓으면 자세히 살펴볼 수 있습니다.
IPC-A-610 기준에 따라 확대경을 사용하여 납땜 접합부 품질, 툼스톤 현상, 불충분한 습윤, 플럭스 잔류물 및 실크스크린 가독성을 점검합니다.
봉인 전에 구매 주문서(PO) 및 자재 명세서(BOM)와 대조하여 라벨 오류, 바코드 불일치, 릴 또는 트레이당 수량 오류 및 포장 자재를 확인합니다.
출하가 승인되기 전에 적합성 인증서, 자재 인증서 또는 시험 보고서 세트에 누락된 부분이 있는 경우 이를 표시합니다.
최종 포장 전에 발견된 고정 부품의 느슨함 또는 조임 토크 미달, 커넥터 장착 불량, 스탠드오프 누락 및 기계적 결합 문제.
MSL 등급을 받은 부품들은 적정 보관 기간 동안의 노출 조건에 대해 검증된 후, 건조제와 습도 표시 카드가 포함된 방습 봉투에 밀봉됩니다.
Every unit's AOI, X-ray, ICT and functional test records are reconciled — any missing or inconsistent record halts the release.
포장 직전에 도면의 공차 기준에 따라 보드의 앞쪽 곡률과 비틀림, 두께 및 외형 치수를 재확인한다.
개정 표시, 날짜 코드 및 부품 표시를 교차 확인하여 구버전이나 혼합된 개정판이 고객에게 전달되는 것을 철저히 방지합니다.
Final inspection is not a single check — it's the consolidation point where every prior test result, every visual pass and every packaging step comes together into one shipping decision.
Results from every upstream station — AOI, X-ray, ICT, flying probe and functional test — are pulled and reconciled against the unit or lot serial number before any physical inspection begins.
AOI · X-ray · ICT · flying probe · functional testEvery unit is inspected under magnification against IPC-A-610 Class 2/3 workmanship criteria — solder joint quality, component placement, silkscreen legibility and conformal coating coverage — along with board warpage, connector seating and standoff height.
IPC-A-610 · 10× magnification · 100% coverage라벨 내용, 바코드 및 수량은 구매 주문서(PO) 및 자재 명세서(BOM)와 대조하여 확인됩니다. 각 제품을 봉투에 넣거나, 상자에 담거나, 릴에 감기 전에 해당 부품에 적합한 정전기 방전(ESD) 방지 포장재가 사용되었는지 확인합니다.
ESD-safe packaging · label vs. PO/BOM audit습기에 민감한 조립품은 J-STD-033 규정에 따라 건조제와 습도 표시 카드가 포함된 방습 봉투에 밀봉됩니다. ESD 포장은 인계 전에 ANSI/ESD S20.20 규정에 따라 검증됩니다.
J-STD-033 · ANSI/ESD S20.20Test reports, certificates of conformance and material certifications are compiled into a single traceable document package for the shipment or lot — ready for customer incoming inspection.
CoC · test reports · material certs전담 OQA 심사관이 출시 전 최종 무작위 검사를 수행하고 승인합니다. 해당 출하분의 결함 추이 및 수율 데이터는 지속적인 개선을 위해 생산 엔지니어링 부서에 피드백됩니다.
OQA sign-off · yield & defect trend feedbackEvery criterion applied at final inspection is traceable to a written standard — not operator judgment.
Every board is inspected under magnification against IPC-A-610 Class 2 or Class 3 acceptance criteria — solder joint fillet quality, component placement and alignment, silkscreen legibility, and conformal coating coverage where specified.
ANSI/ESD S20.20 규정에 따라 전 과정에 걸쳐 ESD 방지 포장이 사용됩니다. 습기에 민감한 소자는 J-STD-033 규정에 따라 건조제와 습도 표시 카드가 포함된 방습 백에 밀봉되며, 외부 포장에는 정확한 보관 기간 라벨이 부착됩니다.
Every shipment ships with a bundled document package: certificate of conformance, all upstream test reports, material and RoHS/REACH certifications, and lot-level traceability records — organized per shipment or lot so your incoming inspection team can verify in minutes.
아래의 모든 매개변수는 당사의 생산 최종 검사 라인을 반영한 것입니다. 모든 주문에는 완전한 검사 기록과 OQA 승인 문서가 동봉되어 발송됩니다.
| 매개변수 | 최종 검사 사양서 | 상태 |
|---|---|---|
| 검사 범위 | 100% — every unit, no AQL sampling | 구입 가능 |
| 제작 기준 | IPC-A-610 클래스 2 / 클래스 3 | 구입 가능 |
| 배율 | 10× – 40× under lit inspection stations | 구입 가능 |
| 일일 검사 대수 | 최대 15,000대 | 구입 가능 |
| 문서 처리 소요 시간 | 최종 승인까지 24시간 남음 | 구입 가능 |
| 포장 옵션 | ESD 트레이 / 테이프 및 릴 / 건조제 포함 MBB | 구입 가능 |
| MSL 핸들링 | J-STD-033 규격 준수, 습도 표시 카드 | 구입 가능 |
| ESD 준수 | ANSI/ESD S20.20 프로그램 | 구입 가능 |
| 결함 누출률 | 50 ppm 미만 목표 | 구입 가능 |
최종 검사는 당사의 전체 품질 시스템이 한데 모이는 단계입니다. 당사가 보유한 모든 인증과 모든 상류 공정 검사 방법은 제품이 출하되기 전 OQA의 최종 승인을 거치게 됩니다.
실제 결함으로 인한 제품들은 고객에게 전달되기 전에 최종 검사 단계에서 차단되었습니다.
1차 자동차 부품 로트에서 발생한 포장 라벨 불일치 문제가, 출하 물량이 창고를 떠나기 전 최종 검사 단계의 PO/BOM 대조 과정에서 적발되었습니다.
출하 전에 불일치 사항을 발견하여, 24시간 이내에 해당 로트 전체에 대해 라벨을 다시 부착하고 재검증을 완료했습니다. 고객은 라벨이 잘못 부착된 제품을 전혀 접하지 않았습니다.
최종 검사 단계에서 Class II 의료기기 프로그램에 대한 전용 MSL 유통기한 점검을 추가하여, J-STD-033 규정에 따라 모든 릴을 밀봉하고 습도 지시제 검증을 실시했습니다.
해당 프로그램은 습기에 민감한 취급과 관련된 지적 사항이 단 한 건도 없이 고객 품질 감사를 통과했으며, 문서화된 MSL 공정이 업계 최고 수준이라는 평가를 받았습니다.
중공업 조립품에 대해 반복적으로 제기된 운송 중 손상 클레임은 반품된 제품에 대한 최종 검사 과정에서 완충 처리가 부적절했던 데서 기인한 것으로 밝혀졌다.
새로운 포장 사양이 표준 OQA 점검 목록에 반영되었습니다. 그 후 두 분기 동안 운송 중 파손에 대한 클레임이 85% 감소했습니다.
A final inspection stamp is only as good as the process behind it. Ours combines 100% unit coverage, documented standards and a dedicated audit gate — not a rubber stamp on a sampling plan.
We don't rely on AQL sampling at final inspection. Every single board is visually and dimensionally checked before packaging — the only way to guarantee zero surprises at your incoming dock.
Certificates of conformance, test reports and material certifications are bundled and delivered within 24 hours of release — ready for your own incoming inspection team.
당사는 결함 누출률을 공식적인 KPI로 관리하며, 발견된 모든 사항을 생산 엔지니어링 부서에 피드백하여 출하마다 이 수치를 낮추기 위해 노력하고 있습니다.
Final release requires sign-off from a quality reviewer independent of the production line — an extra layer of accountability standard on every order, at no added cost.
최종 검사 및 100% 출하 품질 관리에 관한 자주 묻는 질문.
AOI, X-ray, ICT and flying probe each verify one specific aspect of a board — placement, solder joints, or electrical continuity — at a single point in the process. Final inspection happens last and covers everything those methods don't: cosmetic workmanship, packaging accuracy, documentation completeness, MSL/ESD compliance, and a review that every prior test record is present and passing. It's the consolidation step, not a replacement for upstream testing.
100% — every unit, not a statistical AQL sample. Each board is visually and dimensionally inspected under magnification, and its full test data history is reconciled before it's cleared for packaging. Sampling plans are appropriate for some incoming material checks, but not for outgoing quality control on finished assemblies.
네. 모든 출하 물품에는 적합성 인증서와 함께 종합 시험 보고서 세트, 자재 인증서 및 로트별 추적성 문서가 포함됩니다. 이 모든 서류는 한 묶음으로 정리되어 최종 승인 후 24시간 이내에 전달됩니다.
MSL 등급의 조립품은 J-STD-033 규정에 따라 건조제와 습도 표시 카드가 포함된 방습 백에 밀봉되며, 외부 포장에는 보관 기간과 MSL 등급이 명확하게 표시되어 있습니다. 또한 정전기에 민감한 부품이 장착된 기판의 경우, 모든 포장재는 ANSI/ESD S20.20 규정에 따라 정전기 방전(ESD) 안전 기준을 충족합니다.
The affected unit or lot is held and does not receive OQA sign-off. Depending on the finding, it's routed to rework, re-test, or scrap, and the root cause is logged and fed back to production engineering as part of our defect trend reporting — so the same issue is less likely to recur on the next run.
Yes. We regularly align our final inspection checklist and documentation package to match a customer's own incoming quality requirements — including specific IPC class, additional dimensional checks, or extra certificates — so your receiving team can clear shipments faster.
Tell us about your assembly and quality requirements — our quality team will confirm the final inspection and documentation scope along with your quote.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.