Any-layer HDI with stacked microvias — enabling 0.35 mm BGA fan-out, maximum routing density and the thinnest possible boards for today's most advanced electronic products.
고밀도 상호연결(HDI) PCB는 레이저 드릴링 방식으로 제작된 마이크로비아, 순차적 적층 공정 및 미세 선폭 이미징 기술을 활용하여, 일반적인 기계식 드릴링 PCB로는 물리적으로 달성할 수 없는 배선 밀도를 실현합니다.
In any-layer HDI, a microvia can connect any two adjacent layers — not just outer layers to the next inner layer. This routing freedom eliminates the layer-jumping constraints of conventional designs, enabling SoC fan-out at 0.4 mm and 0.35 mm BGA pitch.
The result: smaller boards, fewer layers, shorter signal paths and better electrical performance — all simultaneously.
Get HDI Quote →
HDI는 단순히 더 정밀한 PCB가 아닙니다. 이는 전자 제품 설계에서 물리적으로 가능한 한계를 넓혀주는, 완전히 새로운 상호 연결 아키텍처입니다.
In standard PCBs, routing between non-adjacent layers requires a through-hole via that occupies space on every layer. In any-layer HDI, a 0.10 mm microvia connects only the two layers it needs to — leaving all other layers free for signal routing. This single change allows routing density increases of 2–4× over the same layer count on a standard board.
any-layer · stacked & staggered microvias · sequential lamination최신 AI 프로세서, 모바일 SoC 및 고대역폭 메모리 칩은 0.35mm 및 0.4mm 피치의 BGA 패키지로 출하됩니다. 이러한 피치에서는 표준 드릴(최소 구멍 직경 0.2mm)이 패드 사이로 들어갈 수 없습니다. 0.10mm 레이저 비아와 비아-인-패드(VIA-IN-PAD) 채움 기능을 갖춘 모든 레이어 HDI가 이러한 부품에 대해 양산 가능한 유일한 솔루션입니다.
0.35 mm pitch BGA · via-in-pad · 0.10 mm laser viaA 10-layer HDI board is physically smaller than the 20-layer standard board it replaces. Shorter traces mean lower propagation delay, less insertion loss and reduced power consumption. For DDR5, PCIe 5.0 and 5G RF interfaces, signal quality often improves by moving to HDI — not just maintaining it.
shorter trace = lower loss · DDR5 / PCIe 5.0 · signal integrity모든 파라미터는 당사의 ISO 9001 프로세스를 통해 검증됩니다. 임피던스가 제어된 모든 주문에는 TDR 임피던스 보고서가 함께 제공됩니다.
| 레이어 수 | 4 – 30 layers (any-layer HDI) |
| 최소 트레이스 / 스페이스 | 2.5 / 2.5 밀 |
| 레이저 비아의 최소 직경 | 0.10 mm |
| 최소 BGA 피치 | 0.35 mm (패드 내 비아) |
| 순차적 라미네이션 공정 | 최대 6회의 빌드업 사이클 |
| 판 두께 | 0.4 mm – 3.2 mm |
| 제어 임피던스 | ±5% TDR verified |
| 표면 마감 | ENIG / ENEPIG / OSP / 침지식 Ag |
| IPC 조립 표준 | Class 2 default · Class 3 on request |
| 시제품 제작 기간 | 48h express · 5 days standard |
HDI fabrication requires multiple press cycles with laser drilling and plating between each — a fundamentally more complex process than standard PCB manufacturing.
내부 구리 층은 포토리소그래피 이미징 및 습식 에칭을 통해 패턴화됩니다. 산화막 처리를 통해 적층 접착을 위한 표면이 준비됩니다.
Core layers and prepreg are stacked in optical registration and hot-pressed at 180°C. First build-up layers are added.
0.10 mm microvias are formed by CO₂ laser with ±15 µm positional accuracy. Via walls are cleaned by plasma desmear.
비전기적 구리 시드층을 비아 벽면에 형성하고, 전기분해 구리 도금을 통해 목표 두께까지 두껍게 만듭니다. 패드 내 비아(Via-in-pad)는 채워진 후 평탄화 처리되어 평평한 SMT 랜드를 형성합니다.
소형화, 고속 신호, 첨단 패키징 기술이 접목된 모든 제품.
총 두께 0.8mm 미만, 0.4mm 피치의 BGA 팬아웃을 갖춘 10층 이상의 플래그십 모바일 메인보드.
스마트워치, TWS 이어버드, 피트니스 트래커 등 기판 공간의 1mm³도 소중히 여겨야 하는 제품들.
자동차 인식 시스템에 사용되는 고해상도 카메라 프로세서 보드 및 라이다(LiDAR) 신호 처리 장치.
5G 스몰 셀 기저대역 보드, 광 트랜시버 모듈 및 차세대 네트워크 스위칭 ASIC.
소형화가 필요한 연속 건강 모니터링 기기, 인슐린 펌프 및 이식형 제어 전자 장치.
두께가 1.2mm 미만인 얇은 코어 HDI 메인보드에서 DDR5, PCIe 5.0 및 Thunderbolt 4를 배선합니다.
디스플레이, 카메라 및 신호 처리 전자 부품이 최소한의 공간을 공유하는 혼합 현실 컴퓨팅 보드.
DIN 레일 하우징에 프로세서, 무선 및 필드버스 인터페이스를 통합한 소형 엣지 AI 보드.
일반 PCB와 달리, HDI의 품질은 각 적층 공정마다 확인되어야 합니다. 당사의 공정에는 모든 인증 로트에 대해 공정 간 AOI 검사, 레이저 드릴 정렬 검사 및 도금 후 미세 단면 분석이 포함됩니다.
실제 디자인, 실제 사양, 실제 결과.
안드로이드 플래그십 스마트폰 메인보드의 0.4mm BGA 피치, 0.10mm 마이크로 비아, 비아-인-패드(VIA-IN-PAD) 충진, 0.68mm 총 두께.
양산 개시 시 1차 수율 99%. 18개월 보증 기간 동안 마이크로비아 관련 현장 고장 건수 제로. 기판 면적이 이전 설계 세대보다 22% 더 작음.
MIPI CSI-2 controlled impedance, 0.5 mm BGA fan-out, ENIG, -40°C to +85°C rated for an 8 MP surround-view automotive camera module.
자동차용 열충격 검증에서 첫 시도 만에 통과했습니다. MIPI 아이 다이어그램은 사양을 15%의 여유로 충족했습니다. OEM 프로그램의 SOP 마일스톤을 예정대로 달성했습니다.
총 두께 0.28 mm, 생체적합성 ENIG 코팅이 적용된 7일용 심전도 모니터링 패치용 초저기생성 아날로그 프런트엔드.
첫 제출 시 CE MDR Class IIa 인증 획득. 50만 대 출하되었으며 보드 수준 결함은 단 한 건도 발생하지 않았습니다. 임상용 홀터와 동등한 심전도(ECG) 신호 품질을 자랑합니다.
엔지니어들이 레이어 수에 관계없이 HDI 기판을 주문하기 전에 가장 자주 묻는 기술적 질문들.
Standard HDI (1+N+1 or 2+N+2) only allows microvias on the outer build-up layers — inner layers still use through-hole vias for connections between them. Any-layer HDI allows a microvia between any two adjacent layers, giving full routing freedom without through-hole vias occupying space on every layer. Any-layer enables the routing density needed for 0.35–0.4 mm pitch BGAs.
Our standard minimum laser via diameter is 0.10 mm using CO₂ or UV laser, with positional accuracy of ±15 µm. For special applications, consult our engineering team. The via pad diameter is typically 0.25 mm minimum (0.10 mm via + 0.075 mm annular ring per side).
Yes. 0.35 mm pitch BGA fan-out requires via-in-pad with copper fill and planarisation. Our process achieves a flat, solderable surface directly over the microvia — compatible with standard paste printing and reflow assembly. 0.4 mm pitch fan-out is routinely achieved on all any-layer HDI builds.
We support up to 6 sequential lamination build-up cycles, corresponding to a maximum of 30 layers in an any-layer HDI construction. Each cycle adds one pair of build-up layers. Most HDI designs for mobile and wearable applications use 2–4 cycles (8–14 layers total).
ENIG(무전해 니켈-침지 금 도금)는 HDI 기판에 권장되는 표면 마감 처리 방식입니다. 이 방식은 0.35mm 피치 BGA 조립과 호환되는 평평하고 납땜이 용이한 표면을 제공하며, 피부 접촉이 있는 용도에 적합합니다. SMT 외에도 와이어 본딩이 필요한 용도의 경우 ENEPIG(팔라듐 층 포함)를 권장합니다.
Via-in-pad places a microvia directly under a component pad — typically a BGA pad. The via must be copper-filled and planarised to provide a flat solder surface. Specify via-in-pad when your BGA pitch is ≤0.5 mm and there is insufficient space for dog-bone escape routing, or when you need to minimise solder joint inductance on high-speed power delivery networks.
Gerber 파일과 적층 사양을 보내 주시기 바랍니다. 당사의 HDI 엔지니어들이 영업일 기준 8시간 이내에 상세한 DFM 보고서와 견적을 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.