From connected sensors and smart speakers to energy monitors and home automation hubs — compact, low-power PCBs with multi-protocol RF performance built for mass production.
모든 스마트 홈 기기는 작고 신뢰할 수 있는 PCB에서 시작됩니다. 당사는 이러한 기기에 동력을 공급하는 대량 생산용 다중 프로토콜 기판 제작을 전문으로 합니다.
RF에 최적화된 스택업 구조와 임피던스 제어 트레이스를 갖춘 모든 레이어 HDI 기판은 Matter 인증 스마트 홈 허브에서 Wi-Fi 6, Bluetooth 5.3, Zigbee 및 Thread의 동시 공존을 지원합니다.
Ultra-thin polyimide flex and rigid-flex circuits with biocompatible solder mask fit 5 mm × 10 mm form factors for BLE-connected fitness bands and body-worn sensor patches.
8-layer isolated multilayer boards on V-0 laminate meet IEC 60950 creepage and clearance requirements for mains-connected smart plugs delivering ±1% energy measurement accuracy.
Compact 4-layer HDI boards with sub-2 µA sleep current keep battery-powered smart locks and keypad access sensors running for years on a single CR2032 cell.
비디오 도어벨 및 실내·실외 카메라의 좁은 케이스 내부에 2.5/2.5 mil 트레이스/스페이스 레이아웃을 적용한 HDI 다층 기판을 사용하여 고속 이미지 센서 및 Wi-Fi 6 인터페이스를 구현합니다.
릴레이 등급의 ENIG 접점과 주전원 절연 간극을 갖춘 다층 PCB는 스마트 온도 조절기, 댐퍼 액추에이터 및 수요 반응형 HVAC 제어기를 구동합니다.
세심한 접지 평면 설계와 기생 성분 최소화를 적용한 저전력 4층 기판은 LoRaWAN 및 BLE 환경 센서 노드의 배터리 수명을 코인 셀 하나로 5년까지 연장합니다.
RF에 최적화된 다층 기판은 Zigbee 또는 Thread 메시 무선 통신 기능을 조광 가능한 LED 드라이버 회로와 통합하여, 연결형 스마트 전구 및 조명 제어 모듈을 구현합니다.
IoT devices must be cheap, tiny, power-sipping and RF-transparent simultaneously — while meeting global regulatory requirements in dozens of markets.
단일 스마트 홈 기기에는 하나의 보드에 Wi-Fi 6, Bluetooth 5.3, Zigbee 및 Thread가 통합될 수 있습니다. 감도 저하 없이 RF 공존, 안테나 격리 및 공유 주파수 대역을 관리하려면 세심한 스택업 설계, 안테나 배치 및 임피던스 제어가 필요합니다.
Wi-Fi 6 · BT 5.3 · Zigbee · Thread · 2.4 GHz coexistenceIoT sensor nodes must run for years on a coin cell. Board design choices — trace resistance, parasitic capacitance, ground plane continuity — directly affect standby current by orders of magnitude. Getting the PCB right saves battery specification decisions downstream.
sub-µA sleep · parasitic minimisation · ground plane designIoT 제품은 CE(EU), FCC(미국), TELEC(일본) 및 기타 수십 개의 규제 지역으로 출하됩니다. PCB 적층 구조, RF 트레이스 배선 및 차폐 캐비티 설계는 방출 및 내성 테스트 결과에 영향을 미칩니다. PCB 단계에서 이를 올바르게 설계하면 비용이 많이 드는 챔버 재시험을 피할 수 있습니다.
CE · FCC · TELEC · emissions-optimised stackup작은 기판 면적, 다중 프로토콜 RF 및 저전력 요구 사항에 특화된 PCB 기술.
컴팩트한 IoT 허브 폼 팩터에서 최대 배선 밀도를 구현하는 모든 레이어 HDI. 안테나 클리어런스 구역이 포함된 RF 최적화 스택업, 임피던스가 제어된 Wi-Fi 및 블루투스 트레이스, 일관된 RF 커넥터 성능을 보장하는 ENIG 마감 처리가 통합되어 있습니다.
Ultra-thin polyimide flex and rigid-flex for IoT wearables and body-worn sensors. Biocompatible solder mask, dynamic flex capability and form factors as small as 5 mm × 10 mm boards with BLE SoC integration.
Double-insulation multilayer PCBs for mains-connected IoT devices — smart plugs, energy monitors and demand-response controllers. IPC-compliant creepage and clearance distances, flammability V-0 laminates, ENIG finish for relay contacts.
아래의 모든 파라미터는 IATF 16949 및 IPC-A-600 Class 3 요구 사항에 따라 검증되었습니다. 모든 주문에는 전체 시험 보고서와 자재 추적 정보가 함께 제공됩니다.
| 매개변수 | 자동차용 등급 | 상태 |
|---|---|---|
| 레이어 수 | 2 – 30 layers, any-layer HDI | 구입 가능 |
| 최소 트레이스 / 스페이스 | 2.5 / 2.5 밀 | 구입 가능 |
| 레이저 비아 직경 | 최소 0.10 mm | 구입 가능 |
| 표면 마감 | ENIG / OSP / 침지식 Ag | 구입 가능 |
| 판 두께 | 0.3 mm – 3.2 mm | 구입 가능 |
| 제어 임피던스 | ±5% TDR verified | 구입 가능 |
| RF 최적화 적층 구조 | Wi-Fi / BT / Zigbee 사전 인증 완료 | 구입 가능 |
| 시제품 제작 기간 | 48시간 특급 / 5일 일반 | 구입 가능 |
| 규정 준수 지원 | CE / FCC / RoHS / REACH 인증을 받은 자재 | 구입 가능 |
IoT 제품은 수십만 개 단위로 출하됩니다. 대량 생산 시 기판 불량률이 1%만 발생해도 막대한 보증 및 물류 비용이 발생합니다. 당사의 DFM 검토, 100% AOI 검사, 그리고 엄격히 관리되는 RF 적층 설계를 통해 양산이 시작되기 전에 현장 고장을 사전에 방지합니다.
Real automotive PCB challenges — and how we solved them.
Wi-Fi 6, BT 5.3, Zigbee 및 Thread를 동시에 통합한 10층 HDI 기판. RF 공존을 고려한 적층 구조, 제어된 안테나 피드 임피던스, 전체 ENIG 마감 처리.
4가지 프로토콜 모두 첫 번째 챔버 테스트에서 규제 요건을 충족했습니다. 제품은 예정보다 8주 앞서 출하되었습니다. 첫 생산 로트 투입 시 제조 수율은 98.4%를 기록했습니다.
4-layer HDI board for a LoRaWAN / BLE environmental sensor. Sub-2 µA sleep current, 5 cm × 3 cm board area, CR2032 battery target of 5-year life.
Achieved 1.8 µA measured sleep current — beating target spec. 5-year battery life confirmed by accelerated drain testing. Zero board-level failures in 1M units shipped.
실시간 에너지 모니터링 기능이 탑재된 스마트 플러그용 8층 절연 다층 기판. IEC 60950 간격 기준 준수, V-0 등급 라미네이트, Wi-Fi + BT 듀얼 밴드, CT 센서 인터페이스.
CE and FCC certification achieved at first submission. Energy measurement accuracy ±0.8% across full rated current range. 500,000-unit volume run with 99.6% production yield.
Automotive procurement teams need more than a PCB factory — they need a certified partner with documented processes, fast engineering response and the depth to solve problems before the production line.
IoT 제품 개발은 빠르게 진행됩니다. 당사의 48시간 익스프레스 프로토타입 서비스와 8시간 DFM 검토 서비스를 통해 귀사의 엔지니어링 팀은 공급망에 발목 잡히지 않고 원활하게 업무를 진행할 수 있습니다.
We maintain prequalified RF stackups for 2.4 GHz multi-protocol, 5 GHz Wi-Fi and sub-GHz LoRa/Z-Wave applications — reducing your time from schematic to FCC/CE-ready prototype.
Any-layer HDI with 0.10 mm laser vias allows you to pack more capability into the small form factors that smart home products demand — without compromising signal integrity.
엔지니어링 샘플부터 백만 대 규모의 양산까지. 전 세계 계약 제조업체 및 유통 센터로의 DDP 배송. CE 마킹을 위한 RoHS/REACH 관련 서류 준비 완료.
당사의 IoT 및 스마트 홈 PCB 엔지니어링 팀이 귀사의 설계를 검토한 후, 8 영업시간 이내에 상세한 DFM 보고서와 견적서를 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.