From fixture-based In-Circuit Test on high-volume runs to boundary scan on dense digital boards and custom functional test against your spec — full electrical verification before a board ever leaves our floor.
ICT, 바운더리 스캔, 하이팟 및 기능 테스트는 각각 서로 다른 고장 모드를 대상으로 합니다. 마우스를 올려놓으면 자세히 확인할 수 있습니다.
허용 오차 범위를 벗어난 값을 파악하기 위해 회로 내에서 저항, 커패시터 및 인덕터를 고속으로 측정합니다.
전체 ‘베드 오브 네일(bed-of-nails)’ 네트워크 검증은 생산 속도로 모든 테스트 지점에서 끊어진 연결 및 의도하지 않은 브리징을 탐지합니다.
Hipot 및 절연 저항 테스트를 통해 기판에 선 전압이 가해지기 전에 전원 평면 간의 절연 불량 여부를 파악할 수 있습니다.
사양에 따른 강화된 기능 테스트를 수행하면, 네트 레벨 테스트에서는 통과했으나 실제 운영 시 제대로 작동하지 않는 오류를 포착할 수 있습니다.
JTAG 체인 테스트를 통해 물리적 프로브 접근이 불가능한 BGA 및 고밀도 디지털 기판의 상호 연결 결함을 파악할 수 있습니다.
기능 테스트를 통해 고객의 전력 예산 사양에 따라 레일 전압, 전압 조정 및 부하 응답을 검증합니다.
맞춤형 기능 테스트 장치는 실제 신호 입출력을 통해 보드가 의도된 기능을 종단 간에 정상적으로 수행하는지 확인합니다.
부하 상태에서 장기간 번인 사이클을 수행함으로써, 보드가 고객에게 전달되기 전에 초기 불량으로 인한 고장을 선별해 냅니다.
대량 ICT를 위한 ‘베드 오브 네일(bed-of-nails)’ 고정 장치가 필요하든, 테스트 사양에 맞춘 맞춤형 기능성 지그가 필요하든, 이 공정은 재현성과 추적 가능한 데이터를 확보할 수 있도록 설계되었습니다.
Our test engineers review your test specification, netlist and BOM to define the right method — ICT, boundary scan, functional, hipot, or a combination — and design the fixture or program accordingly.
Method selection · fixture designICT의 경우, 고객사의 기판 테스트 포인트 레이아웃에 맞춰 맞춤형 베드 오브 네일(bed-of-nails) 고정 장치를 제작합니다. 바운더리 스캔 및 기능 테스트의 경우, 고객사의 사양에 따라 테스트 프로그램을 구축하고 I/O 시뮬레이션을 검증합니다.
5–10 day typical ICT fixture build새로운 고정구 또는 프로그램은 양산 시작 전에, 정상으로 확인된 참조 보드와 불량으로 확인된 참조 보드를 대상으로 테스트를 수행하여, 정상 제품에는 통과 판정을, 불량 제품에는 불합격 판정을 올바르게 내리는지 확인합니다.
정상/불량 상관관계Boards are run through ICT and/or functional test at production speed, powering up the assembly and verifying it performs its intended function against your test spec — rails, I/O, load response and timing.
시간당 최대 600개의 보드모든 테스트 결과는 자동으로 기록됩니다. 통계적 공정 관리(SPC)를 통해 수율 추이를 추적하고 편차를 조기에 감지하며, 로트, 배치 또는 일련번호 단위로 보고서를 확인할 수 있습니다.
Real-time SPC · yield trend reportingFrom bed-of-nails fixtures to boundary scan and custom functional jigs — matched to your volume and test spec.
A custom fixture with hundreds of spring-loaded pins contacts every test pad simultaneously, verifying component values, orientation and opens/shorts in seconds — the fastest per-unit test method once volume justifies the tooling.
IEEE 1149.1-compliant boundary scan chains test interconnects on components with no physical probe access — essential for BGA, QFN and other fine-pitch digital packages where ICT probe access is limited or impossible.
AC/DC hipot and insulation resistance testing verifies dielectric withstand and safety isolation on power-carrying and safety-critical boards, per UL and IEC test methods — essential wherever mains or high-voltage isolation is safety-critical.
Custom jigs simulate real-world inputs, loads and signal conditions, powering up the assembled board and verifying it performs its intended electrical function against your test spec — including extended burn-in for early failure screening.
귀사의 생산량 및 신뢰성 요구 사항에 맞춰 조정된 ICT, 바운더리 스캔, 하이팟 및 기능 테스트 매개변수. 모든 생산 배치마다 완전한 테스트 보고서와 SPC 데이터가 함께 제공됩니다.
| 매개변수 | 전기 시험 능력 | 상태 |
|---|---|---|
| ICT 장비 처리 기간 | 5–10 working days typical | 구입 가능 |
| 테스트 커버리지 | 최대 98%의 순/구성 요소 커버리지 | 구입 가능 |
| 생산 처리량 | 200–600 boards/hour (volume dependent) | 구입 가능 |
| 전압 시험 범위 | 0–1,000V DC · up to 4,000VAC hipot | 구입 가능 |
| 현재 시험 범위 | µA leakage to 30A functional load | 구입 가능 |
| 바운더리 스캔 커버리지 | JTAG 호환 네트에 대해 최대 95% | 구입 가능 |
| 번인 시간 | 24–168 hours, configurable | 구입 가능 |
| 기능 테스트 | 고객 사양에 따라 제작된 맞춤형 고정구 | 구입 가능 |
| 데이터 및 수율 보고 | 실시간 SPC, 로트/일련번호 단위 기록 | 구입 가능 |
모든 생산 시험 가동 내역은 로트 단위의 추적 가능성을 확보하여 기록됩니다. 각 배치에 대해 요청 시 시제품 상관 분석, SPC 추세 데이터 및 수율 보고서를 제공해 드립니다.
Real production electrical test challenges — and how we solved them.
대량 생산되는 12층 ECU 기판용으로 제작된 맞춤형 ‘베드 오브 네일(bed-of-nails)’ 고정 장치로, 모든 배치에 대해 IATF 표준에 부합하는 SPC 데이터 로깅 기능을 갖추고 있습니다.
첫 번째 연간 생산 주기 동안 현장 고장이 단 한 건도 발생하지 않았습니다. SPC 추세 데이터를 통해 프로브 마모 문제를 조기에 파악함으로써 수율 저하를 방지할 수 있었습니다.
여러 개의 완전히 덮개 처리된 BGA가 장착된 고밀도 디지털 기판으로, 물리적 프로브 접근이 불가능한 경우 경계 스캔을 통해 테스트되었습니다.
바운더리 스캔을 통해 ICT만으로는 물리적으로 접근할 수 없었던 BGA 패키지 내부의 두 군데 상호 연결 단선 부위를 발견했다.
유전 내압 시험이 필요하며, 실제 부하 조건을 시뮬레이션하는 맞춤형 기능 테스트 장치가 필요한 안전 중요 전력 모듈.
맞춤형 기능 테스트 장비와 72시간 번인 테스트를 통해 제품이 고객에게 출하되기 전에 초기 수명 단계에서 발생할 수 있는 두 건의 고장을 선별해 걸러냈습니다.
Volume production needs more than a probe — it needs repeatable fixtures, real coverage data and a partner who can flag drift before it becomes a field failure.
We combine test methods so components with no physical probe access are still verified — coverage isn't limited to what a bed-of-nails alone can reach.
맞춤형 ‘베드 오브 네일(bed-of-nails)’ 테스트 장치는 생산 속도로 시간당 수백 개의 보드를 테스트하므로, 전기적 검증 작업이 핵심 공정 일정에 영향을 미치지 않도록 합니다.
모든 테스트 결과는 SPC 추세 차트에 반영되므로, 수율의 편차나 특정 결함 유형이 현장 문제로 대두되기 전에 미리 감지되어 해결됩니다.
전기적 안전 기준 준수가 필수적인 기판의 경우, UL 및 IEC 시험 방법에 따라 절연 및 절연 내압 시험이 수행됩니다.
ICT, 바운더리 스캔, 하이팟 및 기능 테스트에 대한 자주 묻는 질문과 이들 중 어떤 것을 선택해야 하는지.
ICT verifies individual components and net connections — values, orientation, opens/shorts — with the board unpowered or lightly biased. Functional test powers the board up and exercises it as it would run in the field, verifying that it actually performs its intended function against your test spec. Most production programs use both: ICT to catch build defects, functional test to confirm end-to-end performance.
ICT fixtures typically pay for themselves once you're running consistent volumes — the per-unit test time is much faster than flying probe once the fixture exists. If your design is still changing or your volume is low-to-medium, flying probe usually makes more economic sense since it avoids the 5–10 day fixture lead time and tooling cost entirely.
바운더리 스캔은 많은 디지털 IC에 내장된 IEEE 1149.1 JTAG 표준을 활용하여, 핀에 물리적 프로브를 접촉시키지 않고도 상호 연결을 테스트하는 방식입니다. 이는 기계적 프로브 접근이 사실상 불가능한 BGA, QFN 및 기타 미세 피치 패키지에 필수적이며, 일반적으로 ICT와 병행하여 실행함으로써 고밀도 디지털 기판의 테스트 커버리지 공백을 메웁니다.
Hipot testing applies a high AC or DC test voltage between isolated conductors — typically mains-to-secondary or power-to-chassis — to confirm the insulation can withstand normal operating stress without breaking down. We measure leakage current and insulation resistance against your target spec, which is standard on any board where electrical safety isolation matters.
Yes. Burn-in runs assembled boards under load at elevated temperature for a configurable period — typically 24 to 168 hours — to accelerate and screen out infant-mortality failures before shipment. It's commonly specified for automotive, industrial and safety-critical programs where field failures carry a high cost.
Every board's test result is logged automatically — pass/fail, fault type and location where applicable — and rolled up into SPC yield trend reports at lot, batch or serial-number level. Reports are available on request for every production run, and we'll flag any yield drift proactively rather than waiting for a formal review.
넷리스트, BOM 및 테스트 사양서를 보내주시면, 당사의 테스트 엔지니어링 팀이 적합한 테스트 방법 조합을 제안해 드리고 8 영업시간 이내에 견적을 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.