From collaborative robot joints and vision systems to autonomous mobile robots and drone controllers — compact, high-reliability PCBs engineered for the precision demands of modern robotics.
현대 로봇의 모든 관절, 센서, 액추에이터는 정밀하게 설계된 PCB에 의존합니다. 당사는 이 모든 구성 요소를 공급합니다.
굽힘 반경이 0.5mm인 동적 리지드-플렉스 기판은 55mm 크기의 소형 협업 로봇 관절 하우징 내부에서 기판 간 커넥터를 없애줍니다.
Any-layer HDI boards with 0.4 mm BGA pitch routing pack vision processing and AI inference compute into board areas as small as 50×50 mm.
자율 이동 로봇의 항법을 위해 LiDAR SLAM, 카메라 SLAM 및 5G 연결을 동시에 처리하는 16층 HDI 기판.
그리퍼, 힘 센서 및 공구 교환 장치 전자 부품에 전원을 공급하기 위해 좁은 기계적 통로를 통과하도록 가공된 소형 리지드-플렉스 기판.
실시간 서보 드라이브 및 3상 모터 제어 루프를 위한 EtherCAT 필드버스 인터페이스가 탑재된 고신뢰성 다층 기판.
폐루프 로봇 모션 제어 시스템에 신호를 공급하는 듀얼 인코더 및 토크 센서 인터페이스용 소형 HDI 기판.
주요 AGV 구동 컨트롤러 및 산업용 로봇 암 제어 장치용 고-Tg 라미네이트 기반의 IPC Class 2/3 다층 기판.
항공 로봇 시스템의 소형 비행 제어기 및 페이로드 짐벌 전자 장치를 위한 경량 리지드-플렉스 기판.
Robots must be compact, fast and fault-free. Board failures stop production lines and autonomous operations — both are unacceptable.
코봇 관절은 직경 60mm의 하우징 내부에 장착되어야 하며, 이 하우징에는 모터 컨트롤러, 인코더 인터페이스, 안전 워치독 및 필드버스 노드가 포함되어야 합니다. 전기적 성능이나 신뢰성을 저하시키지 않으면서 이러한 고밀도 배치를 구현할 수 있는 것은 올레이어 HDI 및 리지드-플렉스 기판뿐입니다.
any-layer HDI · rigid-flex · 60mm housing · 2.5/2.5 milEtherCAT and SERCOS real-time fieldbus protocols tolerate nanosecond-level jitter. At robot arm servo cycle times of 125 µs, PCB trace routing, differential pair matching and ground plane design directly affect motion quality and repeatability.
EtherCAT · differential pairs · ground plane · ±0.5 mil로봇 엔드 이펙터는 지속적인 진동과 충격에 노출될 뿐만 아니라, 때때로 절삭유나 세정제에 노출되기도 합니다. PCB는 IEC 60068 진동 시험 기준을 충족해야 하며, 레이어 구성은 콘포멀 코팅 또는 IP67 등급의 포팅 컴파운드와 호환되어야 합니다.
IEC 60068 vibration · IP54–IP67 · conformal coat ready로봇 공학 응용 분야는 첨단 PCB 기술의 전 영역에 걸쳐 있습니다. 당사는 모든 제품을 자체 생산합니다.
The primary technology for robotics — rigid sections for component mounting, flex regions to route around joints and through tight mechanical passages. Eliminates board-to-board connectors (a major failure point in moving machines) and reduces assembly mass.
Maximum routing density in compact compute boards for vision processing, SLAM navigation and AI inference. Stacked microvias allow BGA routing at 0.4 mm pitch in board areas as small as 50 mm × 50 mm.
로봇 메인 컨트롤러, AGV 구동 시스템 및 기능 안전 모니터링 보드용 IPC Class 2 및 Class 3 다층 기판. 모터 발열 부근에 위치한 기판용 고 Tg 라미네이트, 냉각액에 노출되는 부위용 콘포멀 코팅.
아래의 모든 파라미터는 IATF 16949 및 IPC-A-600 Class 3 요구 사항에 따라 검증되었습니다. 모든 주문에는 전체 시험 보고서와 자재 추적 정보가 함께 제공됩니다.
| 매개변수 | 자동차용 등급 | 상태 |
|---|---|---|
| 레이어 수 | 2 – 30 layers, any-layer HDI | 구입 가능 |
| 최소 트레이스 / 스페이스 | 2.5 / 2.5 밀 | 구입 가능 |
| 레이저 비아 직경 | 최소 0.10 mm | 구입 가능 |
| 리지드-플렉스 | 동적 플렉스, 0.5 mm 굽힘 반경 | 구입 가능 |
| 작동 온도 | -40°C to +125°C | 구입 가능 |
| 표면 마감 | ENIG / ENEPIG / OSP / 침지식 Ag | 구입 가능 |
| 제어 임피던스 | ±5% TDR verified | 구입 가능 |
| 시제품 제작 기간 | 48시간 특급 / 5일 일반 | 구입 가능 |
| IPC 조립 표준 | 2등급 기본, 3등급은 요청 시 제공 | 구입 가능 |
A failed PCB in a production robot stops an entire line. Our DFM review, 100% electrical test and flexible stackup expertise ensure your robot boards arrive ready to deploy — and stay deployed.
Real automotive PCB challenges — and how we solved them.
7축 협업 로봇 관절용 초소형 리지드-플렉스 보드. 직경 55mm 하우징 제약 조건 충족, EtherCAT 슬레이브, 3상 모터 드라이버, 듀얼 엔코더 인터페이스 및 안전 워치독을 단일 보드에 통합.
기판 수정 없이 기계적 시제품 단계에서 첫 물리적 호환성이 확인되었습니다. 모든 EtherCAT 타이밍 사양을 충족했습니다. 현재 로봇 팔은 월 2,000대 규모로 양산 중입니다.
12-layer HDI board for an edge AI smart camera integrating NVIDIA Jetson module, dual GigE vision ports, IMX sensor interface and PoE++ power management in 85 mm × 55 mm.
99% first-pass electrical yield at production entry. Thermal performance 12°C below competing board design due to optimised via-in-pad thermal stack. Customer reduced heatsink by 30%.
LiDAR SLAM, 카메라 SLAM, 모터 제어 및 5G 연결을 동시에 처리하며 총 전력 소모량이 25W인 AMR 내비게이션 컴퓨터용 16층 HDI 기판.
All SI specifications met at -40°C cold soak. AMR fleet has accumulated 500,000 operational hours across 12 warehouse sites with zero board-level failures reported.
Automotive procurement teams need more than a PCB factory — they need a certified partner with documented processes, fast engineering response and the depth to solve problems before the production line.
로봇 개발은 스프린트 방식으로 진행됩니다. 당사의 48시간 익스프레스 프로토타입 제작 및 8시간 DFM 검토 서비스를 통해 공급망 지연 없이 기계 및 전기 팀의 협업이 원활하게 이루어집니다.
We design rigid-flex stackups for robot joints in-house — no third-party fab handoff. Your connector-elimination strategy and flex region geometry are validated by our engineers before a single panel is pressed.
0.10mm 레이저 비아를 적용한 모든 레이어 HDI는 로봇 하우징에 필요한 콤팩트한 기판 공간에 완벽한 연산 및 제어 기능을 집약합니다. 별도의 외부 브레이크아웃 보드나 리본 케이블 하네스가 필요하지 않습니다.
From engineering prototypes to high-volume production. DDP delivery to robot manufacturing sites in Germany, Japan, USA and beyond — with all CE and RoHS documentation.
당사의 로봇 공학 PCB 엔지니어링 팀이 귀사의 설계를 검토한 후, 8 영업시간 이내에 상세한 DFM 보고서와 견적서를 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.