고주파 RF PCB 제조

고주파 PCB
(RF / 마이크로파)

Rogers, Taconic and PTFE laminates from 1 GHz to 110 GHz — stocked in-house, processed in-house, and TDR + VNA verified before every shipment.

로저스 / PTFE / 타코닉 최대 110 GHz ±5% Impedance TDR + VNA 검증 완료
110GHz
최대 주파수 지원
±5%
임피던스 허용 오차
로저스
4350B · 3003C · RO4003C
30L
최대 레이어 수
VNA
S-파라미터 옵션
고주파 PCB란 무엇인가

RF 시스템이 실제로 작동하게 하는 기판 기술

A high-frequency PCB is built on purpose-designed low-loss laminate — Rogers, Taconic, PTFE or ceramic-filled PTFE — instead of standard FR4. The laminate choice is not a preference. At frequencies above 1 GHz, standard FR4 introduces signal loss and impedance variance that degrades system performance in ways that cannot be compensated by circuit design.

At 10 GHz, a trace on Rogers 4350B has approximately 5× less loss than the same trace on FR4. At 77 GHz — used for automotive radar — FR4 is not a usable transmission medium. The physics of high-frequency signal propagation make laminate selection a critical design decision, not a procurement variable.

Our RF engineers specify the right laminate for your frequency band, thermal environment and cost target — then fabricate, verify with TDR and optionally with VNA before shipment.

Get RF PCB Quote →
고주파 PCB
로저스 4350B PTFE 기판 저손실 라미네이트 제어된 Dk TDR + VNA
기술 및 장점

Why FR4 fails at high frequencies — and what the data shows

유전체 손실과 유전율(Dk) 변동과 관련된 물리적 원리 때문에, 라미네이트 선정은 RF PCB 설계에서 가장 중요한 결정 사항입니다.

01

Dielectric Loss — FR4 vs Rogers 4350B at 10 GHz

FR4's loss tangent (tan δ) of 0.020–0.025 causes signal attenuation of 1–3 dB/cm at 10 GHz. Rogers 4350B has tan δ = 0.0037 — approximately 6× lower loss at the same frequency and geometry. For a 5G base station power amplifier, this difference directly translates to efficiency, thermal dissipation and operating cost at scale.

tan δ FR4 = 0.022 · Rogers 4350B = 0.0037 · 6× less attenuation
02

Dk Variance — Why FR4 Impedance Is Unpredictable

FR4's dielectric constant varies from 4.2 to 4.8 between suppliers and even between production lots from the same supplier. A 50 Ω trace designed to nominal Dk = 4.4 can be 44 Ω or 57 Ω on a different FR4 lot — before fabrication tolerance is even considered. Rogers 4350B has Dk = 3.48 ±0.05 — tight enough to design to with confidence.

FR4 Dk variance ±0.3 · Rogers 4350B Dk = 3.48 ±0.05
03

Hybrid Stackup — RF Performance at Controlled Cost

Most RF + digital mixed designs do not need Rogers on every layer. Outer layers handling RF traces use Rogers or PTFE for signal performance. Inner digital layers handling clocks, power and data buses use standard FR4 at standard cost. Our hybrid stackup design service specifies which layers need low-loss laminate and which do not — optimising performance per dollar.

Rogers outer layers · FR4 inner layers · hybrid stackup · cost optimised
기술 사양

고주파 PCB 전체 사양

모든 RF 라미네이트는 사내에 재고로 보유하고 있습니다. 임피던스가 제어된 모든 제품 주문 시 TDR 임피던스 보고서를 제공합니다. 요청 시 VNA S-파라미터도 제공해 드립니다.

가공 매개변수

최대 작동 주파수최대 110 GHz (Rogers 3003C / PTFE)
임피던스 허용오차±5% TDR verified (±3% on precision orders)
RF 적층판Rogers 4350B · RO4003C · RO3003C · Taconic TLY · PTFE
레이어 수2 – 30 layers
최소 트레이스 / 스페이스2.5 / 2.5 mil (RF: ±0.5 mil tolerance)

성능 및 표준

표면 마감ENIG · ENEPIG · Electrolytic Hard Gold
캐비티 밀링Waveguide integration · connector pockets
백드릴고속 디지털 레이어의 스텁 제거를 통한 방법
검증TDR standard · VNA S-parameters on request
시제품 제작 기간48h express · 5 days standard
제조 공정

고주파 PCB의 제조 과정

RF PCB 제조는 표준 PCB 제조 공정에서는 찾아볼 수 없는, 더 엄격한 공정 공차와 RF 전용 검증 단계를 결합한 것입니다.

01
1단계

라미네이트 선정 및 검사

Rogers, Taconic or PTFE laminate is selected per Dk, tan δ and CTE requirements. Incoming Dk is verified against CoC before production begins.

02
2단계

정밀 공차 이미징 및 에칭

Trace width is held to ±0.5 mil (vs ±1 mil on FR4) using optimised photolithography parameters. Verified by SEM measurement on every lot.

03
3단계

캐비티 밀링 및 드릴링

정밀 CNC 밀링 공정을 통해 밀리미터파(mmWave) 기판용 도파관 이음매와 커넥터 장착부를 제작합니다. 하이브리드 적층 기판의 마이크로비아 가공에는 레이저 드릴링 공정을 적용합니다.

04
4단계

TDR/VNA 검증

모든 기판은 TDR을 통해 임피던스 측정을 거칩니다. 모든 기판에 대해 VNA S-파라미터 특성 분석(주입 손실 대 주파수) 결과를 확인할 수 있습니다.

응용 분야

고주파 PCB 기술이 필요한 경우

표준 FR4를 사용할 경우 용납할 수 없는 신호 손실이나 임피던스 편차가 발생하는 응용 분야.

01

5G 기지국 RF

Rogers/PTFE boards for 5G NR sub-6 GHz and mmWave radio units — power amplifiers and antenna feeds.

02

자동차용 레이더

77 GHz ADAS radar front-ends on Rogers 4350B — forward collision, lane departure and blind-spot systems.

03

마이크로파 백홀

6–86 GHz point-to-point backhaul radios used in mobile network infrastructure.

04

전자전

여러 옥타브에 걸친 주파수 대역에서 ESM, 전파 방해 및 신호 정보 수집 시스템용 광대역 RF 기판.

05

위성 통신

LEO/GEO 위성 페이로드 전자 장비 및 VSAT 단말기용 Ka/Ku 대역 송수신기 보드.

06

스펙트럼 분석기 및 VNA

DC에서 110 GHz까지 작동하는 테스트 장비용 저위상잡음 RF 프런트엔드.

07

의료 영상

MRI 그라디언트 코일 구동 장치 및 의료용 레이더(호흡/생체 신호 감지)용 GHz 대역 RF 기판.

08

산업용 레이더 센서

산업용 존재 감지, 수위 측정 및 제스처 감지를 위한 60 GHz 및 77 GHz 기판.

제조 및 품질

RF quality verified with RF instruments — not just optical.

Optical inspection confirms copper is present. TDR confirms impedance is correct. VNA confirms insertion loss meets your link budget. For high-frequency boards, we apply all three — because every unverified PCB variable becomes a variable in your RF system.

  • ISO 9001:2015제3자 감사를 거친 품질 관리
  • 원자재 공급망(CoC)Rogers / Taconic / PTFE Dk and tan δ per lot
  • IPC-A-600 등급 2 / 3RF PCB 적합성 기준
  • RoHS / REACHEU 유해 물질 규정 준수

검사 및 시험 방법

  • TDR Impedance — All Controlled Structures±5% verified per board, report included
  • VNA S-파라미터 특성 분석Insertion loss vs frequency — on request
  • 100% Electrical Test — Flying Probe모든 그물이 확인되었습니다
  • 100% AOI — All Layers자동 광학 검사
  • Trace Width Measurement — SEM로트별 통계적 SPC 데이터
  • Dk Verification — Material Coupon로트별, 로저스/타코닉 사양 확인
  • ENIG Thickness — XRFRF 접점 영역에서의 Ni/Au 균일성
  • 구멍 깊이 확인Milled pocket depth ±0.05 mm
기능 예시

당사에서 제작한 고주파 회로 기판

Real RF PCB challenges — material expertise and process precision delivered.

Automotive · 77 GHz Radar

77 GHz ADAS 레이더 프런트엔드

8-layer Rogers 4350B, 128 antenna feed lines TDR-verified ±4.2%, ENIG, -40°C to +85°C, IATF 16949 documentation.

77GHz
주파수
±4.2%
임피던스
128피드
안테나 선로
결과

모든 안테나 수신 신호가 사양 범위 내에 있습니다. RF 시스템 테스트 결과, 안테나 이득이 시뮬레이션 값보다 +0.8 dB 더 높게 나타났습니다. IATF 16949 FAI는 첫 제출 시 승인되었습니다.

5G · mmWave Beamforming

28 GHz 5G 빔포밍 보드

12층 하이브리드 로저스 4350B/FR4, 64T64R 매시브 MIMO, 캐비티 밀링 공법으로 가공된 패치 안테나 개구부, 0.5mm BGA 빔포밍 IC 팬아웃.

28GHz
주파수
12L 하이브리드
스택업
64×64
MIMO 구성
결과

RF 시스템 테스트 결과가 시뮬레이션치를 상회했습니다. 3분기 연속으로 생산 일정을 준수하며 납품했습니다. 고객사는 HanSphere를 39 GHz 프로그램의 우선 공급업체로 선정했습니다.

T&M · 67 GHz VNA

67 GHz VNA RF 프런트엔드 보드

20층 로저스 3003C, 캐비티 밀링 가공된 도파관 전환부, RF 인터페이스에 전해 경질 금 도금, 기판별 VNA 특성 분석 완료.

67GHz
주파수
20L
레이어
VNA ✓
모든 게시판
결과

67 GHz에서 시뮬레이션 결과와 0.3 dB 이내의 삽입 손실을 보입니다. 모든 기판은 개별 VNA 데이터 파일과 함께 출하됩니다. RF 재작업 없이 계측기 교정 시 100% 합격합니다.

FAQ

고주파 PCB에 관한 자주 묻는 질문

RF 라미네이트 선정, 임피던스 제어 및 제작에 관한 기술적 질문.

We hold in-house stock of: Rogers 4350B (Dk 3.48, tan δ 0.0037), RO4003C (Dk 3.55, tan δ 0.0027), RO3003C (Dk 3.00, tan δ 0.0013), Taconic TLY (Dk 2.17, tan δ 0.0009), Taconic RF-35 (Dk 3.50, tan δ 0.0018), and PTFE-based laminates for frequencies above 40 GHz. Material CoC with Dk and tan δ per lot is supplied with every order.

Our standard RF impedance tolerance is ±5%, verified by TDR measurement and reported per board. For precision applications (test instruments, VNA boards, precision phase-matched lines), ±3% tolerance is available — this requires ±0.5 mil trace width control and Dk-verified laminate selection. Specify your required tolerance at enquiry stage.

Yes — full 2-port VNA S-parameter measurements (S11, S21 insertion loss vs frequency) are available on all boards as an optional service. The measurement data is supplied as Touchstone (.s2p) files and can be imported directly into your RF simulation software for correlation to design intent. Specify VNA measurement at enquiry stage.

Our standard Rogers 4350B and RO4003C process supports applications to approximately 40 GHz. For W-band (75–110 GHz) applications, we use Rogers RO3003C or PTFE-based laminates with cavity milling for waveguide integration. The practical upper limit depends on laminate choice, copper surface roughness at mmWave frequencies, and connector interface geometry.

하이브리드 스택업은 RF 트레이스가 배선된 외부 층에는 저손실 RF 라미네이트(Rogers, PTFE)를 사용하고, 디지털 전원 및 데이터 신호를 처리하는 내부 층에는 표준 FR4 또는 고Tg 라미네이트를 사용합니다. 이를 통해 신호 품질이 중요한 부분(외부 RF 트레이스)에서는 RF 성능을 확보하는 동시에, 전체를 Rogers 소재로 제작하는 방식에 비해 비용을 대폭 절감할 수 있습니다. 당사의 RF 엔지니어들은 5G 및 ADAS 레이더 애플리케이션을 위해 일상적으로 하이브리드 스택업을 설계하고 있습니다.

Yes — CNC cavity milling is a standard service for mmWave boards requiring recessed connector launch areas, waveguide transitions and heat spreader pockets. Cavity depth tolerance is ±0.05 mm, wall verticality ±2°. Cavity drawings should be provided as a separate mechanical layer in the Gerber/ODB++ package. Photographs and dimensional inspection reports are available on cavity lots.

견적 받기

Get your RF PCB design reviewed — today.

Gerber 파일과 적층 사양을 보내주십시오. 당사의 RF 엔지니어들이 8시간 이내에 라미네이트 선정, 트레이스 형상 및 비아 배치를 검토해 드립니다.

  • 모든 문의 시 DFM 검토가 포함됩니다
  • NDA signed on request — standard practice
  • 영업일 기준 8시간 이내 답변
  • 48시간 내 시제품 제작 가능
  • 견적 요청 시 별도의 약정이 필요하지 않습니다
고주파 PCB 견적 요청 All files encrypted · Max 80MB · DFM review included

견적 요청하기

아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.

WhatsApp