From oscilloscopes and spectrum analysers to automated test equipment and precision calibration instruments — ultra-low-noise, controlled-impedance PCBs engineered for measurement accuracy.
시험 및 계측 제품은 다른 모든 산업의 성능 하한선을 결정합니다. PCB가 성능의 제약 요인이 되어서는 안 됩니다.
High-Tg low-Dk Isola I-Tera boards holding ±3% controlled impedance and ±0.3 mil trace tolerance, preserving flat frequency response across multi-GHz probe input channels.
로저스(Rogers) 3003C 및 PTFE 다층 기판으로, 캐비티 밀링 공정을 거친 도파관 전환부와 전해 경질 금 접점을 갖추고 있어 최대 110 GHz의 계측기 대역폭을 지원합니다.
24-layer probe interface boards holding ±2% impedance across 256 simultaneous test channels, built with nickel-free gold finish for over 1 million probe-touch service life.
비아 정전용량이 0.1 pF 미만이며 트레이스 인덕턴스가 펨토헨리 단위로 정밀하게 조정된 초저기생 다층 기판으로, 레퍼런스 등급 LCR 및 전력 교정 표준용으로 설계되었습니다.
Controlled-impedance HDI multilayer boards with back-drilled vias and continuous ground planes, minimising noise coupling on 1 nV/√Hz-class acquisition electronics.
VNA를 이용한 제조 후 검증 과정을 거친 낮은 Dk 분산 라미네이트 기판으로, 주파수 스윕 전반에 걸쳐 정확한 소자 임피던스 측정에 필요한 안정적인 기생 특성 분석 결과를 유지합니다.
스플릿 플레인(split-plane)을 피하고 백 드릴(back-drilled) 신호 비아를 적용한 고신뢰성 다층 기판으로, 민감한 측정 회로를 스위칭 전원 단계로부터 격리합니다.
전해식 하드 골드 RF 접점과 캐비티 밀링 가공된 전환부를 갖춘 소형 Rogers 4350B 기판으로, VNA 프로브 어셈블리에서 재현성이 뛰어난 교정 등급의 연결을 제공합니다.
A T&M instrument's PCB is not a carrier — it is part of the measurement system. Every parasitic, every impedance discontinuity and every material choice affects instrument accuracy.
While automotive accepts ±5% impedance tolerance, oscilloscope front-end boards require ±3% or tighter to maintain flat frequency response across bandwidth. This demands tighter trace width control (±0.3 mil), lower Dk variance laminates and VNA post-fab verification — not just TDR.
±3% impedance · ±0.3 mil trace · Dk < 0.001 variance · VNA verifyA 1 nV/√Hz noise floor instrument cannot afford PCB layer stackup choices that introduce ground loop noise, power supply coupling or parasitic resonance. Ground plane continuity, split plane avoidance and via-back-drilling are essential design elements, not optional refinements.
1 nV/√Hz · split plane avoidance · back-drill · ground plane스펙트럼 분석기와 VNA는 밀리미터파 대역에서 작동합니다. 100GHz 이상에서는 FR4 기판의 표준 마이크로스트립이 허용할 수 없는 손실을 보입니다. 따라서 Rogers 3003, Isola I-Tera MT40 및 세라믹 충전 PTFE를 사용해야 하며, 도파관 및 커넥터 통합을 위해 캐비티 밀링 가공이 필요합니다.
Rogers 3003 · PTFE · 110 GHz · cavity milling · waveguide선택하는 모든 라미네이트는 형상과 표면 마감에 따라 측정 결과에 영향을 미칩니다. 당사는 정밀 기기에 필요한 제품을 제작합니다.
High-Tg low-Dk laminates (Isola I-Tera, Rogers 4350B) for controlled impedance acquisition boards. Tighter trace tolerance of ±0.3 mil achieved with our advanced photolithography process. VNA verification available on all acquisition-critical boards.
40 GHz 이상에서 작동하는 계측기용 로저스 3003C, 타코닉 RF-35 및 PTFE. 캐비티 밀링 가공된 도파관 전환부, 코인 백 그라운드 플레인, 그리고 모든 RF 프로브 접점에 전해 경질 금 도금 처리. 모든 기판에 대해 TDR 및 VNA 검증 실시.
교정 표준 및 정밀 수동 소자 측정의 경우, PCB 기생 성분을 최소화하는 것은 트레이스 임피던스만큼이나 중요합니다. 당사의 공정은 계측 보드에서 0.1 pF 미만의 비아 정전용량과 펨토헨리 단위의 정확도로 매칭된 트레이스 인덕턴스를 제공합니다.
아래의 모든 파라미터는 IATF 16949 및 IPC-A-600 Class 3 요구 사항에 따라 검증되었습니다. 모든 주문에는 전체 시험 보고서와 자재 추적 정보가 함께 제공됩니다.
| 매개변수 | 자동차용 등급 | 상태 |
|---|---|---|
| 레이어 수 | 2 – 30 layers, sequential lamination | 구입 가능 |
| 임피던스 허용오차 | ±3% (standard: ±5%) on precision orders | 구입 가능 |
| 최소 트레이스 / 스페이스 | 2.5 / 2.5 mil (precision: ±0.3 mil tolerance) | 구입 가능 |
| 레이저 비아 직경 | 최소 0.10 mm | 구입 가능 |
| 최대 주파수 | 최대 110 GHz (Rogers 3003C / PTFE) | 구입 가능 |
| 표면 마감 | ENIG / ENEPIG / 전해 경질 금 도금 | 구입 가능 |
| 백드릴 | 고주파 기판용 비아 스텁 제거 | 구입 가능 |
| 검증 | TDR 및 VNA를 이용한 제조 후 측정 서비스 제공 | 구입 가능 |
| 라미네이트 옵션 | 로저스 / 이솔라 I-테라 / 타코닉 / PTFE / 세라믹 PTFE | 구입 가능 |
T&M customers need quantified process capability, not qualitative claims. We provide TDR reports, trace width measurement data and laminate Dk certification with every precision order — so you know your instrument's PCB performance before assembly.
Real automotive PCB challenges — and how we solved them.
16-layer precision board on Isola I-Tera MT40 for a 20 GHz oscilloscope acquisition front-end. ±3% impedance on all probe input lines, back-drilled via stubs, TDR and VNA verified before shipment.
Flat frequency response within ±0.2 dB to 20 GHz confirmed on VNA. Crosstalk between adjacent input channels 6 dB better than previous design. Instrument shipped 6 weeks ahead of programme schedule.
67 GHz 스펙트럼 분석기용 20층 로저스 3003C 기판. 캐비티 밀링 공법으로 가공된 도파관 전환부, 모든 도파관 접합부에 전해 경질 금 도금 처리, 각 기판에 대한 완전한 VNA 특성 분석 수행.
Insertion loss at 67 GHz within 0.3 dB of simulation. All boards shipped with individual VNA data files. First production batch passed instrument calibration at 100% — no RF touch-ups required.
24-layer ATE probe interface board for a wafer-level semiconductor tester. 256 simultaneous test channels, 3 GHz bandwidth per channel, ±2% impedance tolerance, nickel-free gold finish.
256개 채널 모두 초기 조립 시 임피던스 사양을 충족했습니다. 인접 채널 간의 크로스톡은 고객 사양보다 4dB 낮았습니다. 기판의 수명은 첫 번째 교체 전까지 100만 회 이상의 프로브 접촉을 견뎌냈습니다.
Automotive procurement teams need more than a PCB factory — they need a certified partner with documented processes, fast engineering response and the depth to solve problems before the production line.
Our advanced photolithography and etch process delivers ±0.3 mil trace width control, enabling ±3% impedance on precision boards. Every board ships with a TDR report. No estimates, no sampling — measured data.
For mmWave and precision boards, we go beyond TDR — VNA insertion loss measurement is available on every board. Your instrument's RF performance is confirmed at PCB level before assembly begins.
We hold Rogers 3003C, Isola I-Tera MT40 and PTFE in stock. No lead time for material procurement — your mmWave board goes straight into production.
Our T&M engineers review your stackup, impedance structures, via geometry and laminate selection within 8 hours — catching performance-limiting issues before they become expensive respins.
당사의 테스트 및 계측 PCB 엔지니어링 팀이 귀사의 설계를 검토한 후, 8 근무시간 이내에 상세한 DFM 보고서와 견적서를 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.