세라믹 PCB 제조

세라믹 PCB
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
AlN의 열전도도
350°C
최대 작동 온도
DPC
직접 도금 구리 공정
25µm
최소 트레이스 폭 (DPC)
0CTE Δ
SiC/GaN과의 불일치
세라믹 PCB란 무엇인가

유기 PCB가 물리적으로 성능을 발휘할 수 없는 용도에 사용되는 기판

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
세라믹 PCB
Al₂O₃ 96% / 99% AlN 170 W/m·K DPC 프로세스 SiC에 최적화된 CTE HTCC / LTCC
기술 및 장점

세라믹을 유일한 실용적인 기판으로 만드는 세 가지 공학적 현실

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
기술 사양

풀 세라믹 PCB 사양

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

가공 매개변수

기판 재료Al₂O₃ 96% · Al₂O₃ 99% · AlN
열전도도24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
프로세스DPC · HTCC · LTCC
최소 트레이스 / 스페이스25 µm / 25 µm (DPC process)
구리 두께5 µm – 300 µm (DPC)

성능 및 표준

작동 온도-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
표면 마감ENIG · bare Cu · Electrolytic Au
기판 두께0.25 mm – 3.0 mm
표면 거칠기 (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
제조 공정

세라믹 PCB의 제조 과정

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
1단계

기판 준비

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
2단계

PVD 시드층

후속 전기 도금을 위한 균일한 전도성 기판을 확보하기 위해 물리적 기상 증착(PVD/스퍼터링)을 통해 Ti/Cu 또는 Ti/Ni 시드 층을 증착합니다.

03
3단계

전해 구리 도금 및 이미징

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
4단계

표면 마감 및 검사

ENIG(전해 금 도금) 처리가 적용됩니다. 100% 광학 검사, 전기적 테스트 및 박리 강도 테스트를 통해 DPC 공정이 완료됩니다.

응용 분야

세라믹 PCB가 유일한 실행 가능한 기판인 경우

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

SiC 및 GaN 전력 모듈

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

고출력 LED 어레이

접합 온도가 수명을 좌우하는 멀티 다이 LED 어레이 및 자외선(UV) 살균용 알루미나 세라믹.

03

자동차용 SiC 인버터

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

RF 전력 증폭기

동시적인 열 관리 및 전기적 절연이 필요한 RF PA 모듈용 AlN.

05

레이저 다이오드 서브마운트

서브 마이크론 수준의 평탄도가 요구되는 단일 방출형 및 바형 레이저 다이오드용 고정밀 세라믹.

06

항공우주 전력 전자공학

항공전자 장비용 DC-DC 변환기 및 위성 전력 조정 장치에 사용되는 경량 세라믹.

07

의료용 전기수술

전기 수술 발생기 출력 회로용 고전압 절연 세라믹.

08

군사 전력 시스템

극한 온도에서 작동하는 레이더 송수신(T/R) 모듈 전력 단계용 군용 규격 세라믹.

제조 및 품질

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015제3자 감사를 거친 품질 관리
  • 자재 인증Al₂O₃ and AlN substrate purity documentation
  • 열전도율 CoCAlN에 대한 랠트별 레이저 플래시 측정
  • RoHS / REACHEU 유해 물질 규정 준수

검사 및 시험 방법

  • 100% Electrical Test — Flying Probe모든 그물, 모든 기질
  • 100% AOI구리 트레이스 및 치수 검사
  • 구리 박리 강도 시험로트별 DPC 구리-세라믹 접합부 접착력
  • Thermal Conductivity — Laser FlashAlN 기판에 대한 롯별 측정
  • 표면 거칠기 (Ra)다이 부착 표면의 프로파일로메트리
  • 곡률과 평탄도다이 부착 평탄도 측정을 위한 레이저 프로파일로메트리
  • Thermal Cycling -55°C to +350°C요청 시 전원 재시동 적합성 검증
  • XRF 코팅 두께ENIG / Au 도금 두께 측정
Get Ceramic PCB Quote →
기능 예시

당사가 제작한 세라믹 기판

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

150 kW SiC 인버터용 AlN 기판

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
전도도
300µm
Cu 두께
150kW
인버터
결과

접합부-케이스 간 열저항이 경쟁사 알루미나 설계보다 22% 낮습니다. 10,000회 전원 사이클 인증을 통과했습니다. 고객사는 이전 세대 대비 35% 더 높은 전력 밀도를 달성했습니다.

LED · UV-C Disinfection

500W UV-C LED 세라믹 어레이

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
LED 전력
24W/m·K
전도도
120°C
지속적인
결과

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

200 W GaN PA용 AlN 기판

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
RF 전력
50µm
RF 트레이스
AlN
기판
결과

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

세라믹 PCB에 관한 자주 묻는 질문

DPC 세라믹 기판, 소재 선정 및 열적 성능에 관한 기술적 질문.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

견적 받기

Get your ceramic substrate design reviewed — today.

열 설계 요구 사항, 다이 부착 사양 및 전원 사이클링 프로파일을 보내 주십시오. 당사의 세라믹 엔지니어들이 8시간 이내에 적합한 소재를 추천해 드리고 DPC 공정에 대한 검토 결과를 제공해 드립니다.

  • 모든 문의 시 DFM 검토가 포함됩니다
  • NDA signed on request — standard practice
  • 영업일 기준 8시간 이내 답변
  • 48시간 내 시제품 제작 가능
  • 견적 요청 시 별도의 약정이 필요하지 않습니다
세라믹 PCB 견적 요청 All files encrypted · Max 80MB · DFM review included

견적 요청하기

아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.

WhatsApp