Pembuatan PCB Keramik

PCB Keramik
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
Konduktivitas termal AlN
350°C
Suhu operasi maksimum
DPC
Proses Tembaga Plat Langsung
25µm
Lebar jejak minimum (DPC)
0CTE Δ
Ketidakcocokan vs SiC / GaN
Apa itu PCB Keramik?

Substrat untuk aplikasi di mana PCB organik secara fisik tidak dapat berfungsi

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
PCB Keramik
Al₂O₃ 96% / 99% AlN 170 W/m·K Proses DPC CTE yang Sesuai dengan SiC HTCC / LTCC
Teknologi & Keunggulan

Tiga kenyataan di bidang teknik yang menjadikan keramik sebagai satu-satunya substrat yang layak

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
Spesifikasi Teknis

Spesifikasi PCB keramik penuh

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

Parameter Pembuatan

Bahan SubstratAl₂O₃ 96% · Al₂O₃ 99% · AlN
Konduktivitas Termal24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
ProsesDPC · HTCC · LTCC
Min. Jejak / Ruang25 µm / 25 µm (DPC process)
Ketebalan Tembaga5 µm – 300 µm (DPC)

Kinerja & Standar

Suhu Operasional-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
Permukaan AkhirENIG · bare Cu · Electrolytic Au
Ketebalan Substrat0.25 mm – 3.0 mm
Kekasaran Permukaan (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
Proses Produksi

Bagaimana PCB keramik diproduksi

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
Langkah 01

Persiapan Substrat

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
Langkah 02

Lapisan Benih PVD

Lapisan dasar Ti/Cu atau Ti/Ni diendapkan melalui proses deposisi uap fisik (PVD / sputtering) untuk menghasilkan dasar konduktif yang seragam bagi proses pelapisan elektro yang akan dilakukan selanjutnya.

03
Langkah 03

Pelapisan Tembaga Elektrolitik & Pencitraan

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
Langkah 04

Permukaan Akhir & Pemeriksaan

Dilakukan pelapisan ENIG atau pelapisan emas elektrolitik. Proses DPC diselesaikan dengan inspeksi optik 100%, pengujian kelistrikan, dan pengujian kekuatan lepas.

Aplikasi

Di mana PCB keramik merupakan satu-satunya substrat yang layak

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

Modul Daya SiC & GaN

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

Susunan LED Daya Tinggi

Keramik alumina untuk susunan LED multi-die dan desinfeksi UV, di mana suhu sambungan menentukan masa pakai.

03

Inverter SiC untuk Industri Otomotif

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

Penguat Daya RF

AlN untuk modul penguat daya RF yang memerlukan pengelolaan termal dan isolasi listrik secara bersamaan.

05

Submount Dioda Laser

Keramik presisi tinggi untuk dioda laser emitor tunggal dan dioda laser batang yang membutuhkan kerataan di bawah mikron.

06

Elektronika Daya Dirgantara

Keramik yang ringan dan efisien untuk konverter DC-DC avionik dan pengondisian daya satelit.

07

Bedah Elektromedis

Keramik terisolasi tegangan tinggi untuk rangkaian keluaran generator bedah listrik.

08

Sistem Tenaga Militer

Keramik berstandar militer untuk tahap daya modul T/R radar yang beroperasi pada suhu ekstrem.

Manufaktur & Kualitas

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015Sistem manajemen mutu yang diaudit oleh pihak ketiga
  • Sertifikasi BahanAl₂O₃ and AlN substrate purity documentation
  • Konduktivitas Termal CoCPengukuran laser flash per lot pada AlN
  • RoHS / REACHKepatuhan terhadap peraturan Uni Eropa mengenai zat berbahaya

Metode Pemeriksaan & Pengujian

  • 100% Electrical Test — Flying ProbeSemua jaring, semua substrat
  • 100% AOIPemeriksaan jalur tembaga dan dimensi
  • Uji Kekuatan Pengelupasan TembagaAdhesi antarmuka DPC-keramik tembaga per lot
  • Thermal Conductivity — Laser FlashPengukuran per lot pada substrat AlN
  • Kekasaran Permukaan (Ra)Profilometri pada permukaan pemasangan chip
  • Lengkungan dan KerataanProfilometri laser untuk mengukur planaritas pemasangan chip
  • Thermal Cycling -55°C to +350°CUji siklus daya sesuai permintaan
  • Ketebalan Lapisan XRFPengukuran ketebalan lapisan ENIG / Au
Get Ceramic PCB Quote →
Contoh Kemampuan

Substrat keramik yang telah kami buat

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

Substrat AlN untuk Inverter SiC 150 kW

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
Konduktivitas
300µm
Ketebalan Cu
150kW
Inverter
Hasil

Resistansi termal antara sambungan dan casing 22% lebih rendah dibandingkan desain alumina pesaing. Telah lulus uji kualifikasi 10.000 siklus daya. Pelanggan berhasil mencapai kepadatan daya 35% lebih tinggi dibandingkan generasi sebelumnya.

LED · UV-C Disinfection

Susunan LED UV-C Keramik 500 W

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
Daya LED
24W/m·K
Konduktivitas
120°C
Berkelanjutan
Hasil

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

Substrat AlN untuk PA GaN 200 W

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
Daya RF
50µm
jalur RF
AlN
Substrat
Hasil

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

Pertanyaan umum mengenai PCB Keramik

Pertanyaan teknis mengenai substrat keramik DPC, pemilihan bahan, dan kinerja termal.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

Dapatkan Penawaran

Get your ceramic substrate design reviewed — today.

Kirimkan persyaratan termal, spesifikasi pemasangan chip, dan profil siklus daya Anda. Insinyur keramik kami akan memberikan rekomendasi bahan dan tinjauan proses DPC dalam waktu 8 jam.

  • Tinjauan DFM disertakan dalam setiap permintaan informasi
  • NDA signed on request — standard practice
  • Tanggapan dalam waktu 8 jam kerja
  • Tersedia prototipe ekspres dalam waktu 48 jam
  • Tidak perlu komitmen apa pun untuk mendapatkan penawaran harga
Ajukan Permintaan Penawaran Harga PCB Keramik All files encrypted · Max 80MB · DFM review included

Minta Penawaran Harga

Isi detail di bawah ini dan kami akan segera menghubungi Anda.

WhatsApp