Seramik PCB Üretimi

Seramik PCB
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
AlN ısı iletkenliği
350°C
Maksimum çalışma sıcaklığı
DPC
Doğrudan Levha Bakır İşlemi
25µm
Minimum iz genişliği (DPC)
0CTE Δ
SiC / GaN ile uyumsuzluk
Seramik PCB Nedir?

Organik PCB’lerin fiziksel olarak görev yapamayacağı uygulamalar için alt tabaka

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
Seramik PCB
Al₂O₃ 96% / 99% AlN 170 W/m·K DPC Süreci SiC ile CTE uyumlu HTCC / LTCC
Teknoloji ve Avantajlar

Seramiği tek geçerli alt tabaka haline getiren üç mühendislik gerçeği

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
Teknik Özellikler

Tam seramik PCB teknik özellikleri

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

Üretim Parametreleri

Alt Tabaka MalzemesiAl₂O₃ 96% · Al₂O₃ 99% · AlN
Isıl İletkenlik24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
SüreçDPC · HTCC · LTCC
Min. İz / Boşluk25 µm / 25 µm (DPC process)
Bakır Kalınlığı5 µm – 300 µm (DPC)

Performans ve Standartlar

Çalışma Sıcaklığı-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
Yüzey İşlemiENIG · bare Cu · Electrolytic Au
Alt Tabaka Kalınlığı0.25 mm – 3.0 mm
Yüzey Pürüzlülüğü (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
Üretim Süreci

Seramik PCB nasıl üretilir?

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
Adım 01

Alt Tabakanın Hazırlanması

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
Adım 02

PVD Tohum Katmanı

Ti/Cu veya Ti/Ni tohum tabakası, sonraki elektrokaplama işlemi için homojen bir iletken taban sağlamak üzere fiziksel buhar biriktirme (PVD / püskürtme) yöntemi ile biriktirilir.

03
Adım 03

Elektrolitik Bakır Kaplama ve Görüntüleme

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
Adım 04

Yüzey İşlemi ve Kontrolü

ENIG veya elektrolitik altın kaplama uygulanır. 0 optik inceleme, elektriksel test ve soyulma mukavemeti testi, DPC sürecini tamamlar.

Başvurular

Seramik PCB’nin tek uygun alt tabaka olduğu durumlarda

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

SiC ve GaN Güç Modülleri

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

Yüksek Güçlü LED Dizileri

Bağlantı noktası sıcaklığının kullanım ömrünü belirlediği çoklu yongalı LED dizileri ve UV dezenfeksiyonu için alümina seramik.

03

Otomotiv Sektörüne Yönelik SiC İnvertörler

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

RF Güç Amplifikatörleri

Aynı anda hem termal yönetim hem de elektriksel yalıtım gerektiren RF PA modülleri için AlN.

05

Lazer Diyot Alt Taşıyıcıları

Mikron altı düzlük gerektiren tek yayıcılı ve çubuk lazer diyotları için yüksek hassasiyetli seramik.

06

Havacılık ve Uzay Güç Elektroniği

Aviyonik DC-DC dönüştürücüler ve uydu güç düzenleme sistemleri için ağırlık açısından verimli seramik.

07

Tıbbi Elektrocerrahi

Elektrocerrahi jeneratör çıkış devreleri için yüksek gerilimli yalıtımlı seramik.

08

Askeri Güç Sistemleri

Aşırı sıcaklıklarda çalışan radar T/R modülü güç aşamaları için askeri standartlara uygun seramik.

Üretim ve Kalite

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015Üçüncü taraflarca denetlenen kalite yönetimi
  • Malzeme SertifikasıAl₂O₃ and AlN substrate purity documentation
  • Isıl İletkenlik CoCAlN üzerinde lot bazında lazer flaş ölçümü
  • RoHS / REACHAB tehlikeli maddelerle ilgili mevzuata uygunluk

Denetim ve Test Yöntemleri

  • 100% Electrical Test — Flying ProbeTüm ağlar, her türlü alt tabaka
  • 0 AOIBakır iz ve boyut denetimi
  • Bakır Soyulma Mukavemeti TestiParti başına DPC Cu-seramik arayüz yapışması
  • Thermal Conductivity — Laser FlashAlN alt tabakaları üzerinde lot bazında ölçüm
  • Yüzey Pürüzlülüğü (Ra)Yonga yapıştırma yüzeylerinde profilometri
  • Kemer ve DüzlükYonga yapıştırma düzlüğü için lazer profilometrisi
  • Thermal Cycling -55°C to +350°CTalep üzerine güç döngüsü onay testi
  • XRF Kaplama KalınlığıENIG / Au kaplama kalınlığı ölçümü
Get Ceramic PCB Quote →
Yetenek Örnekleri

Ürettiğimiz seramik alt tabakalar

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

150 kW SiC İnvertör için AlN Alt Tabakası

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
İletkenlik
300µm
Cu kalınlığı
150kW
İnvertör
Sonuç

Bağlantı noktası-gövde arası termal direnç, rakip alümina tasarımına göre daha düşük. 10.000 güç döngüsü sertifikasyonunu başarıyla geçti. Müşteri, önceki nesle kıyasla daha yüksek güç yoğunluğu elde etti.

LED · UV-C Disinfection

500 W UV-C LED Seramik Dizisi

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
LED gücü
24W/m·K
İletkenlik
120°C
Sürekli
Sonuç

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

200 W GaN Güç Analizörü için AlN Alt Tabakası

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
RF gücü
50µm
RF izi
AlN
Alt tabaka
Sonuç

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

Seramik PCB ile ilgili sık sorulan sorular

DPC seramik alt tabakaları, malzeme seçimi ve termal performans ile ilgili teknik sorular.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

Fiyat Teklifi Alın

Get your ceramic substrate design reviewed — today.

Isıl gereksinimlerinizi, yonga yapıştırma teknik özelliklerinizi ve güç döngüsü profilinizi bize gönderin. Seramik mühendislerimiz 8 saat içinde malzeme önerisi ve DPC süreci incelemesini size iletecektir.

  • Her talebe DFM incelemesi dahildir
  • NDA signed on request — standard practice
  • 8 iş saati içinde yanıt verilir
  • 48 saatlik ekspres prototip hizmeti mevcuttur
  • Fiyat teklifi almak için herhangi bir taahhüt gerekmez
Seramik PCB Teklifi İsteyin All files encrypted · Max 80MB · DFM review included

Fiyat Teklifi İsteyin

Aşağıdaki bilgileri doldurun, kısa süre içinde size geri dönüş yapacağız.

WhatsApp