Produzione di circuiti stampati in ceramica

Circuito stampato in ceramica
(AlN / Al₂O₃ / DPC)

Alumina and aluminium nitride ceramic substrates — up to 170 W/m·K thermal conductivity, stable from -55°C to +350°C, and zero CTE mismatch with SiC and GaN power semiconductors.

AlN / Al₂O₃ Substrate Up to 170 W/m·K −55°C to +350°C DPC / HTCC / LTCC
170W/m·K
Conduttività termica dell'AlN
350°C
Temperatura massima di esercizio
DPC
Processo Direct Plate Copper
25µm
Larghezza minima della traccia (DPC)
0CTE Δ
Disallineamento rispetto a SiC / GaN
Che cos’è un PCB in ceramica?

Il substrato per applicazioni in cui i circuiti stampati organici non sono fisicamente in grado di funzionare

A ceramic PCB uses an alumina (Al₂O₃) or aluminium nitride (AlN) ceramic tile as the substrate — instead of the FR4 or polyimide organic base used in standard PCBs. Copper circuit traces are deposited directly onto the ceramic surface by the Direct Plate Copper (DPC) process or by thick-film screen printing.

The performance difference is not incremental. AlN has thermal conductivity of 170 W/m·K — more than 500× higher than FR4's 0.3 W/m·K. For a 200W SiC MOSFET, this difference means a junction temperature of 180°C on FR4 vs 95°C on AlN — the difference between thermal runaway and reliable operation.

Ceramic substrates are also chemically inert, mechanically stable to 1600°C, and have a coefficient of thermal expansion (CTE) that closely matches SiC (3.7 ppm/°C) and GaN (5.6 ppm/°C) — eliminating the CTE-mismatch fatigue that destroys organic substrate power modules under thermal cycling.

Get Ceramic PCB Quote →
Circuito stampato in ceramica
Al₂O₃ 96% / 99% AlN 170 W/m·K Processo DPC CTE compatibile con il SiC HTCC / LTCC
Tecnologia e vantaggi

Tre aspetti ingegneristici che rendono la ceramica l'unico substrato praticabile

When temperature, thermal conductivity or CTE matching exceeds what organic substrates handle — the physics require ceramic.

01

Thermal Conductivity — 500× Better Than FR4

FR4 thermal conductivity: 0.3 W/m·K. Metal core PCB (MCPCB): 1–4 W/m·K. Alumina Al₂O₃: 24 W/m·K. Aluminium nitride AlN: 170 W/m·K. For a 100W power device, this sequence corresponds to junction temperatures of approximately 180°C, 85°C, 45°C and 30°C above ambient respectively. AlN doesn't just perform better — it enables power density levels that organic substrates physically cannot support.

AlN = 170 W/m·K · Al₂O₃ = 24 W/m·K · FR4 = 0.3 W/m·K · 500× difference
02

Zero CTE Mismatch — The End of Thermal Fatigue

SiC has a CTE of 3.7 ppm/°C. FR4's CTE is 14–17 ppm/°C — a 4× mismatch that generates thermal fatigue stress in every power cycle. After 10,000–100,000 cycles, solder joints crack and the device fails. AlN's CTE of 4.5 ppm/°C nearly matches SiC — enabling direct die attach without thermal interface material and module lifetimes measured in decades rather than years.

AlN CTE = 4.5 ppm/°C · SiC CTE = 3.7 ppm/°C · thermal fatigue eliminated
03

Chemical and Temperature Inertness Above 200°C

FR4 epoxy matrix begins to degrade at temperatures approaching its Tg (130–220°C depending on grade) and is attacked by process solvents and harsh cleaning agents. Alumina and AlN ceramics are stable to 1600°C, chemically inert to virtually all industrial solvents and acids, and non-absorbent of moisture. For high-temperature processes, harsh chemical environments and applications requiring 20+ year service life, ceramic is not a premium option — it is the appropriate engineering specification.

stable to 1600°C · chemical inert · moisture-free · 20+ year life
Get Ceramic PCB Quote →
Specifiche tecniche

Specifiche tecniche dei circuiti stampati interamente in ceramica

Al₂O₃ and AlN substrates stocked in-house. Thermal conductivity measured per lot and reported with delivery.

Parametri di produzione

Materiale del substratoAl₂O₃ 96% · Al₂O₃ 99% · AlN
Conduttività termica24 W/m·K (Al₂O₃) · up to 170 W/m·K (AlN)
ProcessoDPC · HTCC · LTCC
Min. Traccia / Spazio25 µm / 25 µm (DPC process)
Spessore del rame5 µm – 300 µm (DPC)

Prestazioni e standard

Temperatura di esercizio-55°C to +350°C (ceramic) · +850°C (HTCC)
CTE (AlN)4.5 ppm/°C — near-match to SiC / GaN
Finitura superficialeENIG · bare Cu · Electrolytic Au
Spessore del substrato0.25 mm – 3.0 mm
Rugosità superficiale (Ra)< 0.1 µm on die-attach surfaces
Get Ceramic PCB Quote →
Processo di produzione

Come viene prodotto un circuito stampato in ceramica

Ceramic substrate fabrication combines ceramic sintering, thin-film deposition and precision electrolytic plating — entirely different from organic PCB manufacturing.

01
Passo 01

Preparazione del substrato

Fired ceramic tile (Al₂O₃ or AlN) is cut to size, lapped and polished to Ra < 0.1 µm on die-attach surfaces. Incoming thermal conductivity is verified by laser flash.

02
Fase 02

Strato di base PVD

Lo strato di base in Ti/Cu o Ti/Ni viene depositato mediante deposizione fisica da vapore (PVD / sputtering) per fornire una base conduttiva uniforme per la successiva galvanoplastica.

03
Fase 03

Rivelazione e placcatura elettrolitica in rame

Copper is electroplated to target thickness (5–300 µm). Circuit traces are patterned by photolithography and etched to final geometry — 25 µm minimum trace width.

04
Fase 04

Finitura superficiale e ispezione

Viene applicata una finitura ENIG (oro elettrolitico). Il processo DPC si conclude con un’ispezione ottica al 100%, un test elettrico e una prova di resistenza alla pelatura.

Applicazioni

Quando il PCB in ceramica è l'unico substrato utilizzabile

High temperature, high current density or CTE-matched die-attach — ceramic is the engineering requirement.

01

Moduli di potenza in SiC e GaN

AlN substrates directly under SiC MOSFET and GaN HEMT die — eliminating thermal interface materials.

02

Matrici di LED ad alta potenza

Ceramica di allumina per array LED a più chip e per la disinfezione UV, dove la temperatura di giunzione determina la durata di vita.

03

Inverter SiC per il settore automobilistico

DPC AlN for automotive traction inverter power modules requiring continuous 150°C junction temperature.

04

Amplificatori di potenza RF

AlN per moduli PA RF che richiedono contemporaneamente gestione termica e isolamento elettrico.

05

Supporti per diodi laser

Ceramica ad alta precisione per diodi laser a emettitore singolo e a barra che richiedono una planarità inferiore al micron.

06

Elettronica di potenza per il settore aerospaziale

Ceramica a bassa densità per convertitori CC-CC nell’avionica e per il condizionamento dell’alimentazione dei satelliti.

07

Elettrochirurgia medica

Ceramica isolante per alta tensione destinata ai circuiti di uscita dei generatori elettrochirurgici.

08

Sistemi di alimentazione militari

Ceramica di tipo militare per stadi di potenza dei moduli T/R radar che operano a temperature estreme.

Produzione e qualità

Ceramic substrate quality — verified for thermal and mechanical performance.

Copper-ceramic interface adhesion is the life-limiting variable in DPC ceramic substrates under power cycling. Our peel strength testing and thermal cycle qualification confirm the interface quality that determines module operating life — not just day-one electrical integrity.

  • ISO 9001:2015Sistema di gestione della qualità sottoposto a verifica da parte di un ente esterno
  • Certificazione dei materialiAl₂O₃ and AlN substrate purity documentation
  • Conduttività termica CoCMisurazione laser flash per singolo lotto su AlN
  • RoHS / REACHConformità alle normative UE in materia di sostanze pericolose

Metodi di ispezione e collaudo

  • 100% Electrical Test — Flying ProbeTutte le reti, ogni tipo di substrato
  • AOI al 100%Controllo delle tracce in rame e delle quote
  • Prova di resistenza alla pelatura del rameAdesione dell'interfaccia DPC-ceramica in rame per lotto
  • Thermal Conductivity — Laser FlashMisurazione per lotto su substrati di AlN
  • Rugosità superficiale (Ra)Profilometria sulle superfici di fissaggio dei chip
  • Curvatura e planaritàProfilometria laser per la planarità del fissaggio dei chip
  • Thermal Cycling -55°C to +350°CCertificazione relativa al ciclo di accensione/spegnimento su richiesta
  • Spessore del rivestimento misurato con XRFMisurazione dello spessore del rivestimento ENIG / Au
Get Ceramic PCB Quote →
Esempi di funzionalità

Substrati ceramici da noi realizzati

Real high-power and high-temperature substrate challenges — solved.

Power Electronics · SiC Inverter

Substrato in AlN per inverter in SiC da 150 kW

DPC AlN, 170 W/m·K, 300 µm copper for bus bar integration, bare copper surface for direct SiC die attach, -55°C to +175°C operating range.

170W/m·K
Conduttività
300µm
Spessore del rame
150kW
Inverter
Risultato

Resistenza termica tra giunzione e involucro inferiore del 22% rispetto al modello concorrente in allumina. Ha superato la qualificazione con 10.000 cicli di alimentazione. Il cliente ha ottenuto una densità di potenza superiore del 35% rispetto alla generazione precedente.

LED · UV-C Disinfection

Matrice ceramica a LED UV-C da 500 W

Al₂O₃ 99%, 24 W/m·K, ENIG finish, 8×8 multi-die array, continuous 120°C operating temperature for UV-C disinfection module.

500W
Potenza dei LED
24W/m·K
Conduttività
120°C
Continuo
Risultato

LED junction temperature 28°C lower than equivalent MCPCB design. Efficiency 8% higher at rated power. Module lifespan exceeded 50,000 hours in accelerated life testing.

RF · GaN Power Amplifier

Substrato in AlN per amplificatore di potenza in GaN da 200 W

DPC AlN, 50 µm trace width for RF feed lines, ENIG, CTE-matched to GaN-on-SiC die, 0.1 µm Ra surface for die attach.

200W
Potenza RF
50µm
Traccia RF
AlN
Substrato
Risultato

RF performance met specification at first build without layout revision. Thermal measurements 15°C below simulation. Passed MIL-STD-883 qualification first attempt.

FAQ

Domande frequenti sui circuiti stampati in ceramica

Domande tecniche sui substrati ceramici DPC, sulla scelta dei materiali e sulle prestazioni termiche.

DPC (Direct Plate Copper) deposits a thin PVD seed layer directly onto the ceramic surface, then electrolytically plates copper to target thickness. This achieves fine-line capability (25 µm minimum trace width), thin uniform copper and a very smooth surface finish. Thick-film screen printing applies a conductive paste through a screen mask and fires it — minimum line width is typically 100–150 µm and surface roughness is significantly higher. DPC is preferred for power modules, RF applications and precision circuits. Thick-film is used for resistor networks and sensor substrates.

Choose Al₂O₃ (alumina) when thermal conductivity of 24 W/m·K is sufficient and cost is a primary constraint — suitable for LED drivers, general power electronics and medical devices. Choose AlN (aluminium nitride) when your power device junction temperature budget requires conductivity above 80 W/m·K, when CTE matching to SiC or GaN die is critical, or when operating temperatures exceed 200°C continuously. AlN is approximately 3–4× the cost of alumina.

The minimum copper thickness in our DPC process is 5 µm (for signal-layer applications). Standard power module copper is 100–200 µm. For bus bar and high-current applications, copper up to 300 µm is achievable. Copper thickness affects current carrying capacity, thermal resistance and the required minimum trace width — thicker copper requires wider traces to maintain uniform plating.

Yes — DPC ceramic with bare copper or ENIG finish is suitable for direct die attach using silver sinter paste, gold-tin (AuSn) solder or SAC305 solder. For direct silver sinter, the copper surface must be silver-plated after DPC. The ceramic substrate provides the CTE match to the die and the thermal path to the heat sink, eliminating thermal interface material layers and their associated thermal resistance.

Thermal conductivity of AlN substrates is measured by laser flash analysis (LFA) on material coupons cut from the same production lot as the substrates shipped. We report the measured value in the material Certificate of Conformance (CoC) delivered with each order. Typical measured values for our standard AlN grade are 155–170 W/m·K. If your thermal model requires a specific minimum value, specify it at enquiry stage.

DPC ceramic substrates with copper traces are rated for continuous operation to 350°C. The copper-ceramic bond begins to degrade above 400°C due to differential CTE. For applications requiring operation above 350°C, HTCC (High Temperature Co-fired Ceramic, fired at 1500°C) with refractory metal conductors (W, Mo) is the appropriate technology — consult our engineering team for HTCC capability.

Richiedi un preventivo

Get your ceramic substrate design reviewed — today.

Inviateci le vostre esigenze termiche, le specifiche di fissaggio dei chip e il profilo dei cicli di accensione/spegnimento. I nostri ingegneri specializzati in ceramica vi forniranno una raccomandazione sui materiali e una valutazione del processo DPC entro 8 ore.

  • Revisione DFM inclusa in ogni richiesta di preventivo
  • NDA signed on request — standard practice
  • Risposta entro 8 ore lavorative
  • Disponibile prototipo express in 48 ore
  • Non è necessario alcun impegno per richiedere un preventivo
Richiedi un preventivo per PCB in ceramica All files encrypted · Max 80MB · DFM review included

Richiedi un preventivo

Inserisci i dati qui sotto e ti ricontatteremo al più presto.

WhatsApp