From smartphones and wearables to smart home devices and gaming hardware — high-density, cost-efficient PCBs engineered for fast time-to-market and high-volume production.
소비자 가전 분야에서는 소형화, 신속한 제품 개선, 그리고 비용 관리가 요구됩니다. 당사는 이 세 가지 모두를 지원합니다.
트레이스/간격 2.5/2.5 mil, 레이저 비아 0.10 mm를 갖춘 모든 레이어의 HDI 기판으로, 1 mm 미만의 스마트폰 메인보드에 최대의 연산 성능을 집약합니다.
곡선형 외장 및 움직이는 경첩에 밀착되어야 하는 웨어러블 기기용으로, 0.5mm의 굽힘 반경을 가진 초박형 폴리이미드 리지드-플렉스 회로.
직경 10mm 미만의 초소형 플렉스-리지드 PCB로, 이어버드 본체에 블루투스, 센서 및 배터리 충전 기능을 탑재할 수 있도록 0.3mm 피치 BGA를 지원합니다.
Controlled-impedance multilayer boards up to 30 layers supporting DDR5 and PCIe 5.0 signal paths, 100% TDR-verified to ±5% impedance tolerance.
지속적인 힌지 개폐 동작에 견디도록 설계된 동적 플렉스 및 리지드-플렉스 어셈블리로, 접이식 디스플레이와 슬림한 태블릿 폼 팩터에 최적화되어 있습니다.
DFM(제조 용이성)과 표면 마감 처리 옵션을 적절히 조화시켜, 첫 번째 공정 수율을 저하시키지 않으면서도 까다로운 소비자 가격대를 충족시키는 비용 최적화된 HDI 다층 기판.
무선 스피커 및 프리미엄 헤드폰 전자 기기를 위한, 임피던스 제어 스택업 구조에 5G 및 블루투스 RF 경로가 포함된 고속 다층 기판.
0.3mm 미만의 부품 피치를 갖춘 초박형 플렉스 및 모든 레이어 HDI 기판을 통해 센서, 광학 드라이버 및 처리 장치를 경량 헤드셋 프레임에 집적합니다.
Consumer products demand engineering compromises that industrial electronics never face — cost pressure, extreme miniaturisation and ultra-fast development cycles at the same time.
Modern smartphones pack more computing power than a server rack from ten years ago — into a board thinner than 1 mm. Any-layer HDI, stacked microvias and component pitches below 0.3 mm are now baseline requirements, not advanced features.
any-layer HDI · 2.5/2.5 mil · 0.3mm pitch BGAConsumer product cycles run 6–12 months from concept to retail. Your PCB supplier cannot be a bottleneck. 48-hour express prototypes for engineering validation, fast DFM turnaround and a supplier who communicates in your time zone are non-negotiable.
48h prototype · fast DFM · English supportConsumer electronics budgets leave no room for over-engineering — but field failures drive negative reviews and warranty costs that dwarf the PCB saving. Getting the stackup, DFM and surface finish right the first time is the only cost-efficient approach.
first-pass yield · DFM included · no reworkConsumer electronics spans the full range of PCB technologies — from ultra-thin flex to high-speed multilayer.
Our most advanced HDI capability — stacked and staggered microvias on any layer, minimum 2.5/2.5 mil trace/space. The board technology behind the thinnest and most powerful consumer devices on the market.
구부러지거나 접히거나 곡면 표면에 밀착되어야 하는 웨어러블 기기용 초박형 폴리이미드 플렉스 및 리지드-플렉스 회로. 움직이는 경첩이나 접이식 디스플레이가 장착된 제품을 위한 동적 플렉스 기능.
게임 및 프리미엄 오디오 하드웨어에 사용되는 DDR5, PCIe 5.0, 블루투스 및 5G RF 경로용 임피던스 제어 다층 기판. 출하 전 100% TDR 검증을 통해 임피던스를 확인합니다.
아래의 모든 파라미터는 IATF 16949 및 IPC-A-600 Class 3 요구 사항에 따라 검증되었습니다. 모든 주문에는 전체 시험 보고서와 자재 추적 정보가 함께 제공됩니다.
| 매개변수 | 자동차용 등급 | 상태 |
|---|---|---|
| 레이어 수 | 2 – 30 layers, any-layer HDI | 구입 가능 |
| 최소 트레이스 / 스페이스 | 2.5 / 2.5 밀 | 구입 가능 |
| 레이저 비아 직경 | 최소 0.10 mm | 구입 가능 |
| 표면 마감 | ENIG / ENEPIG / OSP / 침지식 Ag | 구입 가능 |
| 판 두께 | 0.3 mm – 3.2 mm | 구입 가능 |
| 제어 임피던스 | ±5% tolerance, TDR verified | 구입 가능 |
| 시제품 제작 기간 | 48시간 특급 / 5일 일반 | 구입 가능 |
| IPC 조립 표준 | 2등급 기본, 3등급은 요청 시 제공 | 구입 가능 |
| 규정 준수 | CE / FCC / RoHS / REACH | 구입 가능 |
Consumer electronics rework is expensive and schedule-killing. Our DFM review, controlled impedance and 100% AOI ensure your engineering sample arrives ready to test — not ready to rework.
Real automotive PCB challenges — and how we solved them.
플래그십 스마트워치용 초박형 6층 리지드-플렉스 기판. 기판 두께 0.6mm, 동적 플렉스 힌지 영역, 모든 접점 부위에 ENIG 마감 처리, 생체 적합성 솔더 마스크.
50,000개 규모의 양산에서 98%의 1차 수율 달성. 18개월 보증 기간 동안 휨 파손 사례가 단 한 건도 보고되지 않았습니다. 총 4차례의 생산 분량 모두 정시에 납품되었습니다.
Ultra-compact 4-layer HDI board for TWS earbuds, integrating Bluetooth SoC, ANC MEMS mic, touch sensor and PMIC in 12 mm × 8 mm board area.
Design fit production enclosure on first prototype build. 99.2% first-pass at production entry — no layout changes required between DVT and MP.
Wi-Fi 6E, Zigbee, Z-Wave 및 Thread를 동시에 지원하는 10층 RF 최적화 기판입니다. 안테나 피드 라인에 대해 세심한 RF 절연 및 임피던스 제어가 필요했습니다.
첫 번째 테스트에서 RF 성능이 사양을 충족했습니다. 제품은 당초 일정보다 6주 앞서 출시되었습니다. 경쟁사 벤치마크 결과, Wi-Fi 감도가 8dB 향상된 것으로 나타났습니다.
Automotive procurement teams need more than a PCB factory — they need a certified partner with documented processes, fast engineering response and the depth to solve problems before the production line.
48-hour express prototypes for engineering validation, 5-day standard for DVT. We don't add hidden charges — express is a standard service, not an exception.
Every order gets a DFM review — stackup, impedance, DRC, DFM and assembly considerations — returned within 8 hours. No extra charge, no opt-in required.
Any-layer HDI, stacked microvias, 2.5/2.5 mil trace/space — in-house. No outsourcing of critical HDI processes to a third-party job shop.
5개의 엔지니어링 샘플부터 50만 개 규모의 양산 주문까지. 유럽, 미주 또는 아시아에 위치한 귀사의 제조 현지로 DDP 조건에 따라 배송해 드립니다.
당사의 가전제품 PCB 엔지니어링 팀이 귀사의 설계를 검토한 후, 8영업시간 이내에 상세한 DFM 보고서와 견적서를 보내드리겠습니다.
아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.
당사는 사용자 경험을 개선하기 위해 쿠키를 사용합니다. 자세한 내용은 당사의 개인정보 처리방침.