플렉시블 PCB(FPC) 제조

연성 PCB
(FPC / 플렉스 회로)

Polyimide flex circuits with rolled-annealed copper — rated for millions of dynamic bend cycles, biocompatible on request, and available in thicknesses as low as 0.05 mm.

폴리이미드 기판 0.5 mm 굽힘 반경 다이나믹 플렉스 생체적합성 ENIG
0.5mm
최소 동적 굽힘 반경
PI
폴리이미드 기판
0.05mm
최소 트레이스 폭
M+
동적 휨 사이클
48h
익스프레스 프로토타입
플렉시블 PCB란 무엇인가

구부러지고, 접히며, 제품에 완벽하게 밀착되는 회로

A flexible PCB (FPC) is a circuit built on a thin polyimide (PI) base instead of rigid FR4 — allowing it to bend, fold and flex repeatedly without trace fracture or delamination.

The key material difference is rolled-annealed (RA) copper foil. Unlike standard electrodeposited copper, RA copper has a crystalline grain structure aligned with the rolling direction — giving it the fatigue resistance to survive millions of bend cycles without work-hardening and cracking.

Beyond bending, flex circuits eliminate harnesses and board-to-board connectors — each one a potential failure point and a source of assembly variation. One continuous flex circuit replaces multiple components and the labour to install them.

Get Flex PCB Quote →
연성 PCB
PI 기판 RA 구리 다이나믹 플렉스 생체적합성 ENIG 커버레이 보호
기술 및 장점

경성 회로 기판 및 커넥터에 비해 플렉스 회로 기판이 갖는 세 가지 공학적 장점

Flex는 단순히 ‘구부릴 수 있는 PCB’가 아닙니다. 이 제품은 조립 아키텍처를 변화시켜 신뢰성을 높이고, 무게를 줄이며, 경성 기판으로는 구현할 수 없는 폼 팩터를 가능하게 합니다.

01

Eliminate Connectors — Eliminate Failure Points

Board-to-board connectors in portable and wearable products fail through mechanical stress, fretting corrosion and tolerance stack-up. Replacing a connector with a flex circuit removes the failure mode entirely. In applications with millions of mating cycles (laptop hinges, wearable clasps), flex is not an option — it is the only viable solution.

connector elimination · zero fretting · lower field failure rate
02

0.5 mm Dynamic Bend Radius — Millions of Cycles

A properly designed flex circuit with RA copper and correctly oriented traces survives millions of dynamic bend cycles at 0.5 mm bend radius — the equivalent of 15+ years of daily use in a wristband. Standard ED copper at the same bend radius will fracture within tens of thousands of cycles.

RA copper · perpendicular trace orientation · 1M+ cycle qualified
03

생체적합성이 뛰어나며 인체에 무해함

Polyimide base material with ENIG finish is among the most biocompatible PCB constructions available — suitable for skin-contact wearables and, with ISO 10993 material certification, for implantable medical devices. Our PI materials are compatible with ETO sterilisation and gamma radiation, enabling use across the full range of medical device applications.

ISO 10993 · ENIG skin-safe · ETO / gamma sterilisation compatible
기술 사양

풀 플렉스 PCB 사양

동적 휨 성능은 데이터시트상의 추정치가 아닌 사이클 테스트를 통해 확인되었습니다.

가공 매개변수

레이어 수1 – 8 layers flex / 2 – 20 rigid-flex
최소 트레이스 폭0.05 mm 플렉스 / 0.065 mm 표준
최소 굽힘 반경0.5 mm 동적 / 0.3 mm 정적
구리 유형굽힘 부위용 압연 어닐링(RA)
기판 재료Polyimide (PI) — Kapton-equivalent

성능 및 표준

총 두께 (단일층)최소 0.05 mm
표면 마감ENIG / ENEPIG (요청 시 생체적합성)
플렉스 사이클 등급Millions (dynamic) · 100+ (static bend)
IPC 조립 표준IPC-6013 연성 PCB 표준
멸균요청 시 ETO/감마 호환 가능
제조 공정

플렉시블 PCB의 제조 과정

플렉스 기판 제조는 모든 공정 단계에서 표준 경질 PCB 제조와 다른 소재와 공구를 사용합니다.

01
1단계

PI 라미네이트 제작

폴리이미드 필름은 접착제 기반 또는 무접착제 적층 공정을 통해 절단 및 구리 도금 처리됩니다. 동적 플렉스 용도에는 RA 구리 포일이 선택됩니다.

02
2단계

이미징 및 에칭

회로 트레이스는 자외선 리소그래피를 통해 패턴화되고 화학적으로 에칭됩니다. 플렉스 영역에서는 트레이스 폭이 0.05 mm까지 미세하게 구현됩니다.

03
3단계

커버레이 라미네이션

PI 커버레이(솔더 마스크 아님)는 정밀 절단되어 플렉스 영역 위에 적층되며, SMT 패드는 노출된 상태로 남습니다. 보강재는 부품 구역에 접착됩니다.

04
4단계

표면 마감 및 시험

ENIG 또는 ENEPIG 처리는 접점의 장기적인 신뢰성을 확보하기 위해 적용됩니다. 100% 전기 시험 및 휨 사이클 시험을 통해 적합성을 검증합니다.

응용 분야

플렉스 PCB가 리지드 PCB로는 불가능한 것을 실현하는 분야

3차원 공간에서 구부러지거나, 회전하거나, 형태를 맞추거나, 연결되는 모든 제품.

01

웨어러블 기기 및 피트니스 밴드

기판 무게가 사용자 순응도에 영향을 미치는 스마트워치 및 건강 추적기용 초박형 플렉스.

02

TWS 이어버드

직경 5mm의 이어버드 스템 내부에 오디오, 전원 및 터치 감지 신호를 전달하는 마이크로 플렉스 배선.

03

의료용 임플란트

인공와우, 신경자극기 및 망막 보철용 생체적합성 PI 플렉스.

04

카메라 시스템

회전 관절이 있는 미러리스 카메라, 액션 카메라 및 드론 짐벌용 플렉스 리본.

05

로봇공학

Joint-crossing flex circuits in collaborative robot arms — replacing harnesses that wear and fail.

06

노트북 및 폴더블 기기

노트북 디스플레이와 폴더블 폰에 사용되는 힌지 플렉스 케이블은 수백만 회 접힘 주기를 견딜 수 있도록 설계되었습니다.

07

자동차용 센서

좌석 시트, 스티어링 칼럼 및 도어 패널의 플렉스 회로가 부피가 큰 배선 하네스를 대체하고 있다.

08

위성 하위 시스템

질량이 주요 제약 조건인 위성용 전개형 구조물에 사용되는 경량 PI 플렉스.

제조 및 품질

굽힘 사이클 시험을 통해 플렉스 품질이 검증되었습니다.

납품 시 AOI 검사를 통과한 플렉스 회로도 50,000회의 굽힘 사이클 후에는 고장이 발생할 수 있습니다. 당사의 인증 공정에는 양산 전 피로 수명을 확인하기 위한 동적 사이클링 테스트와 굽힘 부위의 미세 단면 분석이 포함됩니다.

  • ISO 9001:2015제3자 감사를 거친 품질 관리
  • IPC-6013유연 회로 기판(PCB) 인증 기준
  • IPC-A-600수용 기준
  • ISO 10993 준수요청 시 생체적합성 시험 실시

검사 및 시험 방법

  • 100% Electrical Test — Flying Probe모든 네트, 모든 보드
  • 100% AOI자동 광학 검사
  • 플렉스 사이클링 검사Per IPC-TM-650 2.4.34 — qualification lots
  • Microsection — Flex Bend Zone구리 피로 및 박리 검사
  • 커버레이 박리 강도IPC-TM-650 2.4.9항에 따라
  • ENIG Thickness — XRF피부 접촉용 보드의 균일성
  • 치수 검증외형 및 구멍 위치
  • 멸균 호환성요청 시 ETO/감마 테스트 실시
기능 예시

당사가 제작한 플렉스 회로

Real flexible PCB challenges — solved.

Wearable · Smartwatch

6층 리지드-플렉스 스마트워치

총 두께 0.6 mm, 힌지 부위에서 200,000회의 동적 휨 사이클, 생체적합성 ENIG, 리지드 SoC 영역에 0.4 mm BGA.

0.6mm
두께
20만
플렉스 사이클
98%
1차 처리
결과

200,000 사이클 인증을 통과했습니다. 기존 커넥터 설계 대비 조립 높이가 0.4 mm 감소했습니다. 2년간의 생산 기간 동안 커버레이 박리 현상이 전혀 발생하지 않았습니다.

Medical · Cochlear Implant

생체적합성 임플란트 플렉스 회로

ISO 10993 규격 소재, ENIG 도금, 트레이스 폭 0.08 mm, ETO 멸균 가능, 정적 굽힘 반경 0.3 mm.

0.08mm
트레이스 폭
0.3mm
굽힘 반경
ISO10993
생체적합성
결과

EU 지정 기관으로부터 생체적합성 인증을 획득했습니다. 800명의 환자를 대상으로 한 이식 후 5년간의 추적 관찰 기간 동안 실패 사례가 단 한 건도 없었습니다.

Robotics · Joint Flex

코봇 관절용 동적 플렉스 회로

RA copper PI flex replacing 14-wire harness in a collaborative robot joint — rated 5 million dynamic cycles at 0.5 mm bend radius.

5M
플렉스 사이클
0.5mm
굽힘 반경
-40°C
내 체온
결과

500만 사이클 인증을 통과했습니다. 조인트 배선 조립 시간이 12분에서 90초로 단축되었습니다. 로봇 도입 후 3년 동안 하네스 결함이 단 한 건도 발생하지 않았습니다.

FAQ

플렉시블 PCB에 관한 자주 묻는 질문

엔지니어들이 플렉스 및 리지드-플렉스 회로 기판을 주문하기 전에 가장 자주 묻는 기술적 질문들.

Our standard flex base material is polyimide (PI) film — chemically equivalent to DuPont Kapton. PI provides the thermal stability (up to 260°C), chemical resistance and mechanical compliance that flex circuits require. For skin-contact and implantable applications, we can confirm ISO 10993 biocompatibility. LCP (Liquid Crystal Polymer) substrate is available for ultra-low-profile millimetre-wave flex applications.

Our standard minimum dynamic bend radius is 0.5 mm for designs using 1 oz (35 µm) copper. Static-fold applications (bent once during assembly) can achieve 0.3 mm. For tighter radii, reduce copper weight to 0.5 oz and increase the number of flex layers to reduce per-layer strain. Our flex engineers review bend radius, trace orientation and copper weight together in the DFM review.

Solder mask is a photoimageable liquid coating — suitable for rigid PCBs where it is not subject to repeated flexing. Coverlay is a laminated PI film with adhesive — it flexes with the circuit without cracking. Flex regions must always use coverlay, not solder mask. SMT pad areas in rigid or stiffened zones can use solder mask for compatibility with standard paste printing and automated optical inspection.

동적 휨이 발생하는 부위에는 반드시 압연 어닐링(RA) 구리를 지정하십시오. RA 구리는 압연 방향과 일치하는 결정립 구조를 가지고 있어, 수백만 회의 굽힘 사이클을 견딜 수 있는 피로 저항성을 갖추고 있습니다. 반면, 전기 도금(ED) 구리는 기둥상 결정립 구조를 가지고 있어 반복적인 굽힘 시 빠르게 가공 경화되며, 동적 적용 환경에서 수만 회의 사이클 내에 파단됩니다. 당사는 모든 휨 관련 주문에 대해 기본적으로 RA 구리를 사용합니다.

Our standard polyimide base material with ENIG finish is widely used in skin-contact wearables without special qualification. For medical device regulatory submissions requiring ISO 10993 biocompatibility documentation, we can provide third-party test reports on request. ETO and gamma sterilisation compatibility is available — specify sterilisation method at the time of enquiry.

We offer FR4 stiffeners (0.2–1.6 mm) bonded with pressure-sensitive adhesive (PSA) for room-temperature assembly, and polyimide stiffeners bonded with thermally cured adhesive for high-temperature applications. Stiffeners are used to rigidise connector termination areas, component mounting zones and through-hole pad areas. Stiffener placement and thickness are reviewed in the DFM process.

견적 받기

Get your flex circuit reviewed — today.

플렉스 설계도나 기계적 사양을 보내주십시오. 당사의 플렉스 엔지니어들이 8시간 이내에 굽힘 반경, 트레이스 방향 및 커버레이 설계를 검토해 드리겠습니다.

  • 모든 문의 시 DFM 검토가 포함됩니다
  • NDA signed on request — standard practice
  • 영업일 기준 8시간 이내 답변
  • 48시간 내 시제품 제작 가능
  • 견적 요청 시 별도의 약정이 필요하지 않습니다
플렉시블 PCB 견적 요청 All files encrypted · Max 80MB · DFM review included

견적 요청하기

아래에 세부 정보를 입력해 주시면 곧 연락드리겠습니다.

WhatsApp