Productie van flexibele printplaten (FPC)

Flexibele printplaat
(FPC / flexibele printplaat)

Polyimide flex circuits with rolled-annealed copper — rated for millions of dynamic bend cycles, biocompatible on request, and available in thicknesses as low as 0.05 mm.

Polyimide-substraat 0,5 mm buigradius Dynamic Flex Biocompatibel ENIG
0.5mm
Minimale dynamische buigradius
PI
Polyimide-substraat
0.05mm
Minimale spoorbreedte
M+
Dynamische flexcycli
48h
Express-prototype
Wat is een flexibele printplaat?

Het circuit dat buigt, vouwt en zich aanpast aan uw product

A flexible PCB (FPC) is a circuit built on a thin polyimide (PI) base instead of rigid FR4 — allowing it to bend, fold and flex repeatedly without trace fracture or delamination.

The key material difference is rolled-annealed (RA) copper foil. Unlike standard electrodeposited copper, RA copper has a crystalline grain structure aligned with the rolling direction — giving it the fatigue resistance to survive millions of bend cycles without work-hardening and cracking.

Beyond bending, flex circuits eliminate harnesses and board-to-board connectors — each one a potential failure point and a source of assembly variation. One continuous flex circuit replaces multiple components and the labour to install them.

Get Flex PCB Quote →
Flexibele printplaat
PI-substraat RA Koper Dynamic Flex Biocompatibel ENIG Coverlay-bescherming
Technologie en voordelen

Drie technische voordelen van flexibele printplaten ten opzichte van starre printplaten met connectoren

Flex is niet zomaar ‘een printplaat die je kunt buigen’. Het verandert de architectuur van je assemblage op manieren die de betrouwbaarheid verbeteren, het gewicht verminderen en vormfactoren mogelijk maken die met stijve printplaten niet haalbaar zijn.

01

Eliminate Connectors — Eliminate Failure Points

Board-to-board connectors in portable and wearable products fail through mechanical stress, fretting corrosion and tolerance stack-up. Replacing a connector with a flex circuit removes the failure mode entirely. In applications with millions of mating cycles (laptop hinges, wearable clasps), flex is not an option — it is the only viable solution.

connector elimination · zero fretting · lower field failure rate
02

0.5 mm Dynamic Bend Radius — Millions of Cycles

A properly designed flex circuit with RA copper and correctly oriented traces survives millions of dynamic bend cycles at 0.5 mm bend radius — the equivalent of 15+ years of daily use in a wristband. Standard ED copper at the same bend radius will fracture within tens of thousands of cycles.

RA copper · perpendicular trace orientation · 1M+ cycle qualified
03

Biocompatibel en lichaamsvriendelijk

Polyimide base material with ENIG finish is among the most biocompatible PCB constructions available — suitable for skin-contact wearables and, with ISO 10993 material certification, for implantable medical devices. Our PI materials are compatible with ETO sterilisation and gamma radiation, enabling use across the full range of medical device applications.

ISO 10993 · ENIG skin-safe · ETO / gamma sterilisation compatible
Technische specificaties

Specificaties voor volledig flexibele printplaten

De dynamische flexibiliteit is bevestigd door cyclustests en niet afgeleid uit specificatiebladen.

Productieparameters

Aantal lagen1 – 8 layers flex / 2 – 20 rigid-flex
Min. lijnbreedte0,05 mm flexibel / 0,065 mm standaard
Min. buigradius0,5 mm dynamisch / 0,3 mm statisch
KopertypeGewalst en gegloeid (RA) voor flexibele zones
BasismateriaalPolyimide (PI) — Kapton-equivalent

Prestaties en normen

Totale dikte (enkelvoudige laag)minimaal 0,05 mm
OppervlakteafwerkingENIG / ENEPIG (op verzoek biocompatibel)
Flex-cyclusclassificatieMillions (dynamic) · 100+ (static bend)
IPC-bouwstandaardIPC-6013-norm voor flexibele printplaten
SterilisatieETO / gamma-compatibel op aanvraag
Productieproces

Hoe flexibele printplaten worden vervaardigd

Bij de fabricage van flexibele printplaten worden in elke stap andere materialen en andere gereedschappen gebruikt dan bij de standaardproductie van stijve printplaten.

01
Stap 01

Voorbereiding van PI-laminaat

Polyimidfolie wordt gesneden en met koper bekleed door middel van lamineren met of zonder lijm. Voor dynamische flexibele toepassingen wordt RA-koperfolie gekozen.

02
Stap 02

Beeldvorming en etsen

De printbanen worden via UV-lithografie aangebracht en chemisch geëtst. Fijne baanbreedtes tot 0,05 mm op flexibele delen.

03
Stap 03

Coverlay-laminering

De PI-afdeklaag (geen soldeermasker) wordt nauwkeurig gesneden en over de flexibele delen gelamineerd, waarbij de SMT-pads vrij blijven. Verstevigingselementen worden op de componentzones aangebracht.

04
Stap 04

Oppervlakteafwerking en keuring

ENIG of ENEPIG wordt toegepast om een langdurige betrouwbaarheid van de contacten te garanderen. Er worden 100% elektrische tests en kwalificatietests met buigcycli uitgevoerd.

Toepassingen

Waar flexibele printplaten presteren waar starre dat niet kunnen

Elk product dat in de 3D-ruimte kan buigen, draaien, zich aanpassen of verbinden.

01

Draagbare apparaten en fitnessbandjes

Ultradunne flexibele printplaat voor smartwatches en fitnesstrackers waarbij het gewicht van de printplaat van invloed is op de gebruiksbereidheid.

02

TWS-oordopjes

Micro-flex-kabels voor audio, stroomvoorziening en aanraakdetectie in de steeltjes van de oordopjes met een diameter van 5 mm.

03

Medische implantaten

Biocompatibele PI-flex voor cochleaire implantaten, neurostimulatoren en netvliesprothesen.

04

Camerasystemen

Flexibele kabels voor spiegelloze camera’s, actiecamera’s en gimbals voor drones met draaibare verbindingen.

05

Robotica

Joint-crossing flex circuits in collaborative robot arms — replacing harnesses that wear and fail.

06

Laptops en opvouwbare apparaten

Flexibele scharnierkabels in laptopschermen en opvouwbare telefoons zijn ontworpen voor miljoenen vouwcycli.

07

Sensoren voor de automobielindustrie

Flexibele printplaten voor de stoelbezetting, de stuurkolom en de deurpanelen vervangen de omvangrijke kabelbomen.

08

Satellietsubsystemen

Lichtgewicht PI-flex voor in de ruimte inzetbare constructies waarbij het gewicht een belangrijke beperkende factor is.

Productie en kwaliteit

De kwaliteit van de flexibele leidingen is gecontroleerd door middel van buigcyclusproeven.

Een flexibele printplaat die bij levering de AOI-controle doorstaat, kan na 50.000 buigcycli toch defect raken. Ons kwalificatieproces omvat dynamische cyclustests en microsecties van de buigzone om de vermoeidheidslevensduur te controleren voordat het product in productie wordt genomen.

  • ISO 9001:2015Door een onafhankelijke instantie gecontroleerd kwaliteitsbeheer
  • IPC-6013Kwalificatienorm voor flexibele printplaten
  • IPC-A-600Aanvaardbaarheidscriteria
  • Voldoet aan ISO 10993Tests op biocompatibiliteit op aanvraag

Inspectie- en testmethoden

  • 100% Electrical Test — Flying ProbeAlle netten, elke plank
  • 100% AOIGeautomatiseerde optische inspectie
  • Flex-fietstestPer IPC-TM-650 2.4.34 — qualification lots
  • Microsection — Flex Bend ZoneControle op kopervermoeidheid en delaminatie
  • Afpelkracht van de deklaagVolgens IPC-TM-650 2.4.9
  • ENIG Thickness — XRFUniformiteit bij platen die in contact komen met de huid
  • Controle van de afmetingenOmtrek en positie van de gaten
  • Geschiktheid voor sterilisatieETO-/gammatest op verzoek
Voorbeelden van mogelijkheden

Flexibele printplaten die we hebben gemaakt

Real flexible PCB challenges — solved.

Wearable · Smartwatch

6-laags rigid-flex smartwatch

Totale dikte 0,6 mm, 200.000 dynamische buigcycli bij het scharnier, biocompatibele ENIG-laag, 0,4 mm BGA op het starre SoC-gedeelte.

0.6mm
Dikte
200.000
Flex-cycli
98%
Eerste doorloop
Resultaat

Kwalificatietest van 200.000 cycli doorstaan. De montagehoogte is met 0,4 mm verlaagd ten opzichte van het vorige connectorontwerp. Geen enkele delaminatie van de afdeklaag tijdens een productierun van twee jaar.

Medical · Cochlear Implant

Biocompatibel flexibel circuit voor implantaten

ISO 10993-conforme materialen, ENIG-afwerking, spoorbreedte 0,08 mm, geschikt voor ETO-sterilisatie, statische buigradius 0,3 mm.

0.08mm
Lijnbreedte
0.3mm
Buigradius
ISO10993
Biocompat
Resultaat

Biocompatibiliteit erkend door een door de EU aangemelde instantie. Geen enkel geval van falen tijdens de follow-up van vijf jaar na implantatie bij 800 patiënten.

Robotics · Joint Flex

Cobot-gewricht met dynamisch flexibel circuit

RA copper PI flex replacing 14-wire harness in a collaborative robot joint — rated 5 million dynamic cycles at 0.5 mm bend radius.

5M
Flex-cycli
0.5mm
Buigradius
-40°C
Mijn temperatuur
Resultaat

De kwalificatietest van 5 miljoen cycli is geslaagd. De montagetijd voor de kabelverbindingen is teruggebracht van 12 minuten naar 90 seconden. In de drie jaar dat de robot in gebruik is, zijn er geen storingen aan de kabelbomen opgetreden.

FAQ

Veelgestelde vragen over flexibele printplaten

Technische vragen die ingenieurs het vaakst stellen voordat ze flexibele en rigide-flexibele printplaten bestellen.

Our standard flex base material is polyimide (PI) film — chemically equivalent to DuPont Kapton. PI provides the thermal stability (up to 260°C), chemical resistance and mechanical compliance that flex circuits require. For skin-contact and implantable applications, we can confirm ISO 10993 biocompatibility. LCP (Liquid Crystal Polymer) substrate is available for ultra-low-profile millimetre-wave flex applications.

Our standard minimum dynamic bend radius is 0.5 mm for designs using 1 oz (35 µm) copper. Static-fold applications (bent once during assembly) can achieve 0.3 mm. For tighter radii, reduce copper weight to 0.5 oz and increase the number of flex layers to reduce per-layer strain. Our flex engineers review bend radius, trace orientation and copper weight together in the DFM review.

Solder mask is a photoimageable liquid coating — suitable for rigid PCBs where it is not subject to repeated flexing. Coverlay is a laminated PI film with adhesive — it flexes with the circuit without cracking. Flex regions must always use coverlay, not solder mask. SMT pad areas in rigid or stiffened zones can use solder mask for compatibility with standard paste printing and automated optical inspection.

Geef voor dynamische buigzones altijd gewalst en gegloeid (RA) koper op. RA-koper heeft een kristallijne korrelstructuur die in de walsrichting is uitgelijnd, waardoor het de vermoeidheidsweerstand heeft om miljoenen buigcycli te doorstaan. Elektrolytisch afgezet (ED) koper heeft een kolomvormige korrelstructuur die bij herhaaldelijk buigen snel verhardt en bij dynamische toepassingen binnen tienduizenden cycli zal breken. Onze standaardkeuze voor alle buigopdrachten is RA-koper.

Our standard polyimide base material with ENIG finish is widely used in skin-contact wearables without special qualification. For medical device regulatory submissions requiring ISO 10993 biocompatibility documentation, we can provide third-party test reports on request. ETO and gamma sterilisation compatibility is available — specify sterilisation method at the time of enquiry.

We offer FR4 stiffeners (0.2–1.6 mm) bonded with pressure-sensitive adhesive (PSA) for room-temperature assembly, and polyimide stiffeners bonded with thermally cured adhesive for high-temperature applications. Stiffeners are used to rigidise connector termination areas, component mounting zones and through-hole pad areas. Stiffener placement and thickness are reviewed in the DFM process.

Vraag een offerte aan

Get your flex circuit reviewed — today.

Stuur ons uw flexontwerp of mechanische specificaties. Onze flexingenieurs zullen binnen 8 uur de buigradius, de oriëntatie van de sporen en het ontwerp van de afdeklaag beoordelen.

  • Bij elke aanvraag is een DFM-beoordeling inbegrepen
  • NDA signed on request — standard practice
  • Reactie binnen 8 werkuren
  • Prototype binnen 48 uur beschikbaar via de spoedservice
  • U hoeft zich niet te binden om een offerte aan te vragen
Vraag een offerte aan voor flexibele printplaten All files encrypted · Max 80MB · DFM review included

Vraag een offerte aan

Vul hieronder de gegevens in en we nemen zo snel mogelijk contact met u op.

WhatsApp