高周波RF基板の製造

高周波プリント基板
(RF/マイクロ波)

Rogers, Taconic and PTFE laminates from 1 GHz to 110 GHz — stocked in-house, processed in-house, and TDR + VNA verified before every shipment.

ロジャース / PTFE / タコニック 最大110 GHz ±5% Impedance TDR + VNA による検証済み
110GHz
最大周波数の対応
±5%
インピーダンス許容差
ロジャース
4350B · 3003C · RO4003C
30L
最大レイヤー数
VNA
Sパラメータオプション
高周波PCBとは

RFシステムを実際に機能させる基板技術

A high-frequency PCB is built on purpose-designed low-loss laminate — Rogers, Taconic, PTFE or ceramic-filled PTFE — instead of standard FR4. The laminate choice is not a preference. At frequencies above 1 GHz, standard FR4 introduces signal loss and impedance variance that degrades system performance in ways that cannot be compensated by circuit design.

At 10 GHz, a trace on Rogers 4350B has approximately 5× less loss than the same trace on FR4. At 77 GHz — used for automotive radar — FR4 is not a usable transmission medium. The physics of high-frequency signal propagation make laminate selection a critical design decision, not a procurement variable.

Our RF engineers specify the right laminate for your frequency band, thermal environment and cost target — then fabricate, verify with TDR and optionally with VNA before shipment.

Get RF PCB Quote →
高周波プリント基板
ロジャース 4350B PTFE基板 低損失ラミネート 制御されたDk TDR + VNA
技術と特長

Why FR4 fails at high frequencies — and what the data shows

誘電体損失や誘電率(Dk)のばらつきに関する物理的特性により、積層板の選定は、RF用PCB設計において最も重要な決定事項となります。

01

Dielectric Loss — FR4 vs Rogers 4350B at 10 GHz

FR4's loss tangent (tan δ) of 0.020–0.025 causes signal attenuation of 1–3 dB/cm at 10 GHz. Rogers 4350B has tan δ = 0.0037 — approximately 6× lower loss at the same frequency and geometry. For a 5G base station power amplifier, this difference directly translates to efficiency, thermal dissipation and operating cost at scale.

tan δ FR4 = 0.022 · Rogers 4350B = 0.0037 · 6× less attenuation
02

Dk Variance — Why FR4 Impedance Is Unpredictable

FR4's dielectric constant varies from 4.2 to 4.8 between suppliers and even between production lots from the same supplier. A 50 Ω trace designed to nominal Dk = 4.4 can be 44 Ω or 57 Ω on a different FR4 lot — before fabrication tolerance is even considered. Rogers 4350B has Dk = 3.48 ±0.05 — tight enough to design to with confidence.

FR4 Dk variance ±0.3 · Rogers 4350B Dk = 3.48 ±0.05
03

Hybrid Stackup — RF Performance at Controlled Cost

Most RF + digital mixed designs do not need Rogers on every layer. Outer layers handling RF traces use Rogers or PTFE for signal performance. Inner digital layers handling clocks, power and data buses use standard FR4 at standard cost. Our hybrid stackup design service specifies which layers need low-loss laminate and which do not — optimising performance per dollar.

Rogers outer layers · FR4 inner layers · hybrid stackup · cost optimised
技術仕様

高周波用PCBの完全な仕様

すべてのRFラミネートは自社で在庫しています。インピーダンス管理製品をご注文いただくたびに、TDRインピーダンスレポートを添付いたします。ご要望に応じて、VNA Sパラメータもご提供可能です。

加工パラメータ

最大動作周波数最大110 GHz(Rogers 3003C / PTFE)
インピーダンス許容差±5% TDR verified (±3% on precision orders)
RFラミネートRogers 4350B · RO4003C · RO3003C · Taconic TLY · PTFE
層数2 – 30 layers
最小トレース/スペース2.5 / 2.5 mil (RF: ±0.5 mil tolerance)

性能と基準

表面仕上げENIG · ENEPIG · Electrolytic Hard Gold
キャビティミリングWaveguide integration · connector pockets
バックドリル高速デジタル層におけるスタブの除去
検証TDR standard · VNA S-parameters on request
プロトタイプの納期48h express · 5 days standard
製造工程

高周波用プリント基板の製造方法

RF用PCBの製造では、標準的なPCB製造には見られない、より厳しいプロセス公差とRF特有の検証工程が組み合わされています。

01
ステップ 01

ラミネートの選定と検査

Rogers, Taconic or PTFE laminate is selected per Dk, tan δ and CTE requirements. Incoming Dk is verified against CoC before production begins.

02
ステップ 02

高精度イメージングおよびエッチング

Trace width is held to ±0.5 mil (vs ±1 mil on FR4) using optimised photolithography parameters. Verified by SEM measurement on every lot.

03
ステップ 03

キャビティのフライス加工および穴あけ加工

高精度CNCフライス加工により、ミリ波基板用の導波管トランジションおよびコネクタポケットを形成します。ハイブリッド積層基板のマイクロビアにはレーザー穴あけ加工を施します。

04
ステップ 04

TDR/VNAによる検証

すべての基板について、TDRによるインピーダンス測定が行われています。また、すべての基板について、VNAによるSパラメータ特性評価(周波数に対する挿入損失)が可能です。

用途

高周波PCBの技術が求められる場合

標準的なFR4を使用すると、許容できない信号損失やインピーダンスのばらつきが生じる用途。

01

5G基地局のRF

Rogers/PTFE boards for 5G NR sub-6 GHz and mmWave radio units — power amplifiers and antenna feeds.

02

自動車用レーダー

77 GHz ADAS radar front-ends on Rogers 4350B — forward collision, lane departure and blind-spot systems.

03

マイクロ波バックホール

6–86 GHz point-to-point backhaul radios used in mobile network infrastructure.

04

電子戦

ESM、妨害電波、信号情報収集システム向けの、複数オクターブの周波数帯域をカバーする広帯域RF基板。

05

衛星通信

LEO/GEO衛星のペイロード電子機器およびVSAT端末向けのKa/Kuバンド用トランシーバーボード。

06

スペクトラムアナライザおよびVNA

直流から110 GHzまで動作する試験装置向けの、低位相ノイズRFフロントエンド。

07

医療用画像診断

MRI用グラディエントコイル駆動装置および医療用レーダー(呼吸・バイタルサイン検知)向けのGHz帯RF基板。

08

産業用レーダーセンサー

産業用存在検知、レベル測定、ジェスチャー検出向けの60 GHzおよび77 GHz基板。

製造・品質

RF quality verified with RF instruments — not just optical.

Optical inspection confirms copper is present. TDR confirms impedance is correct. VNA confirms insertion loss meets your link budget. For high-frequency boards, we apply all three — because every unverified PCB variable becomes a variable in your RF system.

  • ISO 9001:2015第三者による監査を受けた品質管理
  • 原材料のCoCRogers / Taconic / PTFE Dk and tan δ per lot
  • IPC-A-600 クラス 2 / 3RF用PCBの適合基準
  • RoHS / REACHEUの有害物質規制への準拠

検査および試験方法

  • TDR Impedance — All Controlled Structures±5% verified per board, report included
  • VNAによるSパラメータ特性評価Insertion loss vs frequency — on request
  • 100% Electrical Test — Flying Probeすべてのネットが検証済み
  • 100% AOI — All Layers自動光学検査
  • Trace Width Measurement — SEMロットごとの統計的SPCデータ
  • Dk Verification — Material Couponロットごとのロジャース/タコニック仕様確認
  • ENIG Thickness — XRFRFコンタクト領域におけるNi/Auの均一性
  • キャビティの深さの確認Milled pocket depth ±0.05 mm
機能の例

当社が製造した高周波基板

Real RF PCB challenges — material expertise and process precision delivered.

Automotive · 77 GHz Radar

77 GHz ADASレーダー・フロントエンド

8-layer Rogers 4350B, 128 antenna feed lines TDR-verified ±4.2%, ENIG, -40°C to +85°C, IATF 16949 documentation.

77GHz
周波数
±4.2%
インピーダンス
128フィード
アンテナ線
結果

すべてのアンテナの給電は仕様範囲内でした。RFシステムの試験結果では、アンテナ利得がシミュレーション値を+0.8 dB上回りました。IATF 16949のFAIは初回提出で承認されました。

5G · mmWave Beamforming

28 GHz 5G ビームフォーミング基板

12層ハイブリッド基板(Rogers 4350B/FR4)、64T64R マッシブMIMO、キャビティミル加工によるパッチアンテナ開口部、0.5 mm BGAビームフォーミングICのファンアウト。

28GHz
周波数
12Lハイブリッド
スタックアップ
64×64
MIMOの設定
結果

RFシステムの試験結果がシミュレーションを上回った。3四半期連続で納期通りに納品した。顧客は、39 GHzプログラムの優先サプライヤーとしてHanSphereを認定した。

T&M · 67 GHz VNA

67 GHz VNA RFフロントエンド基板

20層のRogers 3003C、キャビティミル加工による導波管トランジション、RFインターフェースには電解ハードゴールドめっきを施し、基板ごとにVNAによる特性評価を実施。

67GHz
周波数
20L
レイヤー
VNA ✓
すべての掲示板
結果

67 GHzにおける挿入損失は、シミュレーション値から0.3 dB以内の誤差です。すべての基板には、個別のVNAデータファイルが同梱されています。RF関連の再作業を必要とせず、計測器の校正において100%合格しています。

FAQ

高周波PCBに関するよくある質問

RFラミネートの選定、インピーダンス制御、および製造に関する技術的な質問。

We hold in-house stock of: Rogers 4350B (Dk 3.48, tan δ 0.0037), RO4003C (Dk 3.55, tan δ 0.0027), RO3003C (Dk 3.00, tan δ 0.0013), Taconic TLY (Dk 2.17, tan δ 0.0009), Taconic RF-35 (Dk 3.50, tan δ 0.0018), and PTFE-based laminates for frequencies above 40 GHz. Material CoC with Dk and tan δ per lot is supplied with every order.

Our standard RF impedance tolerance is ±5%, verified by TDR measurement and reported per board. For precision applications (test instruments, VNA boards, precision phase-matched lines), ±3% tolerance is available — this requires ±0.5 mil trace width control and Dk-verified laminate selection. Specify your required tolerance at enquiry stage.

Yes — full 2-port VNA S-parameter measurements (S11, S21 insertion loss vs frequency) are available on all boards as an optional service. The measurement data is supplied as Touchstone (.s2p) files and can be imported directly into your RF simulation software for correlation to design intent. Specify VNA measurement at enquiry stage.

Our standard Rogers 4350B and RO4003C process supports applications to approximately 40 GHz. For W-band (75–110 GHz) applications, we use Rogers RO3003C or PTFE-based laminates with cavity milling for waveguide integration. The practical upper limit depends on laminate choice, copper surface roughness at mmWave frequencies, and connector interface geometry.

ハイブリッド積層構造では、RF配線が配線される外層に低損失RF積層板(Rogers、PTFE)を使用し、デジタル電源およびデータ信号用の内層には標準的なFR4または高Tg積層板を使用します。これにより、信号品質が重要な部分(外層のRF配線)でRF性能を確保しつつ、全層Rogers構造に比べてコストを大幅に削減できます。当社のRFエンジニアは、5GやADASレーダー用途向けに、日常的にハイブリッド積層構造の設計を行っています。

Yes — CNC cavity milling is a standard service for mmWave boards requiring recessed connector launch areas, waveguide transitions and heat spreader pockets. Cavity depth tolerance is ±0.05 mm, wall verticality ±2°. Cavity drawings should be provided as a separate mechanical layer in the Gerber/ODB++ package. Photographs and dimensional inspection reports are available on cavity lots.

お見積りをご依頼ください

Get your RF PCB design reviewed — today.

Gerberデータと積層要件をお送りください。当社のRFエンジニアが、8時間以内に積層材の選定、配線形状、ビア配置について確認いたします。

  • すべてのお問い合わせにDFMレビューが含まれます
  • NDA signed on request — standard practice
  • 8営業時間以内にご返信いたします
  • 48時間でのプロトタイプ作成が可能
  • お見積もりのご依頼に、ご契約の義務は一切ありません
高周波PCBの見積もり依頼 All files encrypted · Max 80MB · DFM review included

お見積りのお申し込み

以下の詳細をご記入ください。折り返しご連絡いたします。

WhatsApp