高密度配線基板

高密度配線
高密度配線プリント基板

Any-layer HDI with stacked microvias — enabling 0.35 mm BGA fan-out, maximum routing density and the thinnest possible boards for today's most advanced electronic products.

全層HDI 2.5 / 2.5 ミル 0.10 mm レーザービア 最大30層 48時間エクスプレス
2.5mil
最小トレース/スペース
0.10mm
最小レーザービア径
30L
最大レイヤー数
±5%
インピーダンス許容差
48h
エクスプレス・プロトタイプ
HDI PCBとは

世界最薄のデバイスを支える基板構造

高密度配線(HDI)PCBは、レーザー加工によるマイクロビア、順次積層法、および微細配線形成技術を採用することで、従来の機械式ドリル加工によるPCBでは物理的に達成不可能な配線密度を実現しています。

In any-layer HDI, a microvia can connect any two adjacent layers — not just outer layers to the next inner layer. This routing freedom eliminates the layer-jumping constraints of conventional designs, enabling SoC fan-out at 0.4 mm and 0.35 mm BGA pitch.

The result: smaller boards, fewer layers, shorter signal paths and better electrical performance — all simultaneously.

Get HDI Quote →
高密度配線プリント基板
全層HDI 順次ラミネート レーザーマイクロビア ビア・イン・パッド 0.35mm BGA
技術と特長

エンジニアが複雑な設計にHDIを選ぶ3つの理由

HDIは、単に高密度なプリント基板というだけではありません。これは、電子製品の設計において物理的に可能な範囲を広げる、まったく新しい相互接続アーキテクチャなのです。

01

あらゆる層でのマイクロビアの自由度

In standard PCBs, routing between non-adjacent layers requires a through-hole via that occupies space on every layer. In any-layer HDI, a 0.10 mm microvia connects only the two layers it needs to — leaving all other layers free for signal routing. This single change allows routing density increases of 2–4× over the same layer count on a standard board.

any-layer · stacked & staggered microvias · sequential lamination
02

0.35 mm BGA Fan-Out — No Other Technology Works

最新のAIプロセッサ、モバイルSoC、および高帯域幅メモリチップは、0.35 mmおよび0.4 mmピッチのBGAパッケージで出荷されています。これらのピッチでは、標準的なドリル(最小穴径0.2 mm)ではパッド間のスペースに収まりません。0.10 mmのレーザービアとビア・イン・パッドの充填を備えた全層HDIこそが、これらの部品に対して量産可能な唯一の解決策です。

0.35 mm pitch BGA · via-in-pad · 0.10 mm laser via
03

より短い経路、より優れた信号、より低い消費電力

A 10-layer HDI board is physically smaller than the 20-layer standard board it replaces. Shorter traces mean lower propagation delay, less insertion loss and reduced power consumption. For DDR5, PCIe 5.0 and 5G RF interfaces, signal quality often improves by moving to HDI — not just maintaining it.

shorter trace = lower loss · DDR5 / PCIe 5.0 · signal integrity
技術仕様

HDI基板の製造仕様書(完全版)

すべてのパラメータは、当社のISO 9001プロセスを通じて検証されています。インピーダンス制御製品のご注文には、すべてTDRインピーダンスレポートが添付されます。

加工パラメータ

層数4 – 30 layers (any-layer HDI)
最小トレース/スペース2.5 / 2.5 ミル
レーザービアの最小直径0.10 mm
BGAの最小ピッチ0.35 mm(ビア・イン・パッド)
順次ラミネートサイクル最大6回のビルドアップサイクル

性能と基準

ボードの厚さ0.4 mm – 3.2 mm
制御インピーダンス±5% TDR verified
表面仕上げENIG / ENEPIG / OSP / 浸漬Ag
IPC構築基準Class 2 default · Class 3 on request
プロトタイプの納期48h express · 5 days standard
製造工程

How HDI PCB is built — step by step

HDI fabrication requires multiple press cycles with laser drilling and plating between each — a fundamentally more complex process than standard PCB manufacturing.

01
ステップ 01

内層のイメージングおよびエッチング

内部の銅層は、フォトリソグラフィによる露光と湿式エッチングによってパターン化されます。酸化処理により、積層時の接着に備えて表面が整えられます。

02
ステップ 02

最初のラミネートプレス機

Core layers and prepreg are stacked in optical registration and hot-pressed at 180°C. First build-up layers are added.

03
ステップ 03

CO₂ Laser Microvia Drilling

0.10 mm microvias are formed by CO₂ laser with ±15 µm positional accuracy. Via walls are cleaned by plasma desmear.

04
ステップ 04

銅メッキおよび充填

壁面を介して無電解銅のシード層を形成し、電解銅めっきにより所定の厚さまでめっきします。ビア・イン・パッドのビアを充填し、平坦化処理を施して、平坦なSMTランドを形成します。

用途

HDI PCBの技術が求められる場合

小型化、高速信号、および先進的なパッケージングが融合するあらゆる製品。

01

スマートフォン・タブレット

総厚0.8 mm未満、10層以上のフラッグシップ級モバイル用マザーボード。0.4 mmピッチのBGAファンアウトを採用。

02

ウェアラブル&ヒアラブル

スマートウォッチ、TWSイヤホン、フィットネストラッカーなど、基板のスペースが1立方ミリメートル単位で重要となる製品。

03

ADASおよび車載カメラ

自動車用知覚システムにおける高解像度カメラ用プロセッサボードおよびLiDAR信号処理ユニット。

04

5G・通信

5Gスモールセル用ベースバンドボード、光トランシーバーモジュール、および次世代ネットワーク用スイッチングASIC。

05

医療用ウェアラブルデバイス

小型化が求められる連続健康モニタリング装置、インスリンポンプ、および埋め込み型制御電子機器。

06

ノートパソコン&ウルトラブック

基板厚さが1.2 mm未満の薄型コアHDIマザーボードで、DDR5、PCIe 5.0、Thunderbolt 4の配線を実現。

07

AR/VRヘッドセット

ディスプレイ、カメラ、および処理用電子機器が最小限のスペースを共有する、複合現実(MR)用コンピューティングボード。

08

産業用IoTエッジ

DINレールハウジングに、プロセッサ、無線インターフェース、フィールドバスインターフェースを統合したコンパクトなエッジAIボード。

製造・品質

HDI quality — verified at every lamination cycle.

標準的なPCBとは異なり、HDIの品質は各積層サイクルごとに確認する必要があります。当社のプロセスでは、すべての認定ロットについて、サイクル間のAOI検査、レーザードリル位置合わせ検査、およびメッキ後の微細断面検査を実施しています。

  • ISO 9001:2015第三者による監査を受けた品質管理
  • IPC-A-600 クラス 2 / 3IPC-6016に基づくHDIの適合性
  • 国際人材認定マイクロビア技術の認定基準
  • RoHS / REACHEUの有害物質規制への準拠

検査および試験方法

  • 100% AOI — After Each Lamination Cycle層ごとの光学検査
  • 100% Electrical Test — Flying Probeすべてのネット、すべてのボード
  • X-Ray — Microvia Registration Verification積層ビアの位置合わせチェック
  • Microsection — Microvia PlatingIPC-6016 クラス B/C に基づく Cu の厚さ
  • TDRインピーダンス検証±5% on all controlled structures
  • ビアフィル平坦化チェック表面形状測定
  • お辞儀とひねりIPC-TM-650 2.4.22
  • Laser Via Depth — SEM Cross-section適格ロットについて
機能の例

当社が製造したHDI基板

本物のデザイン、本物の仕様、本物の成果。

Consumer · Flagship Mobile

10層・任意層HDIメインボード

フラッグシップAndroidスマートフォンのメインボードにおいて、BGAピッチ0.4 mm、マイクロビア0.10 mm、ビア・イン・パッドの充填、総厚さ0.68 mmを実現。

10L
レイヤー
0.4mm
BGAピッチ
99%
ファーストパス
結果

量産開始時の初回歩留まりは99%。18か月の保証期間中、マイクロビアに起因する現場での故障はゼロ。基板面積は、前世代の設計に比べて22%小型化されている。

Automotive · ADAS Camera

8層構造のADAS用カメラプロセッサ

MIPI CSI-2 controlled impedance, 0.5 mm BGA fan-out, ENIG, -40°C to +85°C rated for an 8 MP surround-view automotive camera module.

8L
レイヤー
MIPI×4
レーン
98%
ファーストパス
結果

自動車用熱衝撃試験の認定を初回で合格しました。MIPIアイダイアグラムは、仕様を15%の余裕をもって満たしました。OEMプログラムのSOPマイルストーンを期日通りに達成しました。

Medical · Wearable ECG

6層HDIウェアラブル心電図パッチ

総厚0.28 mm、生体適合性ENIG、7日間の心電図モニタリング用パッチ向けの超低寄生成分アナログフロントエンド。

0.28mm
厚さ
6L
レイヤー
CEMDR
認定済み
結果

初回申請でCE MDRクラスIIaの認証を取得。500,000台を出荷し、基板レベルの不具合はゼロ。心電図信号の品質は臨床用ホルターモニターと同等。

FAQ

HDI基板に関するよくある質問

エンジニアが、どの層構成のHDI基板を注文する際にも、最も頻繁に尋ねる技術的な質問。

Standard HDI (1+N+1 or 2+N+2) only allows microvias on the outer build-up layers — inner layers still use through-hole vias for connections between them. Any-layer HDI allows a microvia between any two adjacent layers, giving full routing freedom without through-hole vias occupying space on every layer. Any-layer enables the routing density needed for 0.35–0.4 mm pitch BGAs.

Our standard minimum laser via diameter is 0.10 mm using CO₂ or UV laser, with positional accuracy of ±15 µm. For special applications, consult our engineering team. The via pad diameter is typically 0.25 mm minimum (0.10 mm via + 0.075 mm annular ring per side).

Yes. 0.35 mm pitch BGA fan-out requires via-in-pad with copper fill and planarisation. Our process achieves a flat, solderable surface directly over the microvia — compatible with standard paste printing and reflow assembly. 0.4 mm pitch fan-out is routinely achieved on all any-layer HDI builds.

We support up to 6 sequential lamination build-up cycles, corresponding to a maximum of 30 layers in an any-layer HDI construction. Each cycle adds one pair of build-up layers. Most HDI designs for mobile and wearable applications use 2–4 cycles (8–14 layers total).

HDI基板には、ENIG(無電解ニッケル・浸漬金)仕上げが推奨されます。この仕上げは、0.35 mmピッチのBGA実装に対応した平坦ではんだ付け可能な表面を提供し、肌に接触する用途に適しています。SMTに加えワイヤボンディングが必要な用途には、ENEPIG(パラジウム層付き)が推奨されます。

Via-in-pad places a microvia directly under a component pad — typically a BGA pad. The via must be copper-filled and planarised to provide a flat solder surface. Specify via-in-pad when your BGA pitch is ≤0.5 mm and there is insufficient space for dog-bone escape routing, or when you need to minimise solder joint inductance on high-speed power delivery networks.

お見積りをご依頼ください

Get your HDI PCB design reviewed — today.

Gerberファイルと積層仕様をお送りください。当社のHDIエンジニアが、8営業時間以内に詳細なDFMレポートと見積書をご提示いたします。

  • すべてのお問い合わせにDFMレビューが含まれます
  • NDA signed on request — standard practice
  • 8営業時間以内にご返信いたします
  • 48時間でのプロトタイプ作成が可能
  • お見積もりのご依頼に、ご契約の義務は一切ありません
HDI基板の見積もり依頼 All files encrypted · Max 80MB · DFM review included

お見積りのお申し込み

以下の詳細をご記入ください。折り返しご連絡いたします。

WhatsApp