リジッドフレックス基板の製造

リジッド・フレックス基板
(リジッド+フレックスの組み合わせ)

One board replaces multiple PCBs and all the connectors between them — enabling 3D packaging, eliminating assembly failure points and fitting electronics into geometries no other board technology can achieve.

リジッド+フレックスの組み合わせ 3Dパッケージング 最大20層 IPCクラス3 ダイナミック・フレックス
20L
最大レイヤー数
0.5mm
最小曲げ半径
3D
パッケージの形状
IPC 3
利用可能なビルド:std
48h
エクスプレス・プロトタイプ
リジッドフレックスPCBとは

曲げたり、折りたたんだり、部品を取り付けたりできる基板

A rigid-flex PCB combines rigid FR4 sections (for component mounting and connector termination) with continuous polyimide flex regions (for routing between rigid sections) — all in a single laminated assembly.

The critical advantage over separate rigid boards connected by cables or ZIF connectors is the elimination of those connectors. Every board-to-board interface in your assembly is a potential failure point — mechanical fretting, corrosion, tolerance stack-up and mating force fatigue all degrade connector reliability. Rigid-flex removes them permanently.

For medical, aerospace and wearable applications, rigid-flex also enables 3D fold geometries — the board conforms to the internal volume of your enclosure, rather than requiring the enclosure to be designed around a flat board.

Get Rigid-Flex Quote →
リジッド・フレックス基板
リジッド+フレックスの組み合わせ コネクタの排除 3D折り畳み形状 PI Flex Core IPC-6013
技術と特長

エンジニアがマルチボードアセンブリではなくリジッドフレックスを選ぶ3つの理由

Rigid-flex changes the architecture of your product — not just the PCB type.

01

基板間コネクタをすべて排除する

1つのリジッドフレックス基板アセンブリにより、2枚以上のリジッド基板と、それらを接続するZIFや基板間コネクタが置き換えられます。スマートウォッチの場合、これにより基板が3枚から1枚に減り、コネクタに起因する故障要因が完全に排除されます。外科用カメラの場合、信号経路にコネクタが1つも存在せず、3.5 mmのスコープシャフト内を信号が途切れることなく伝送されます。

zero board-to-board connectors · reduced part count · lower field failure rate
02

3D Packaging — The Board Fits the Enclosure

リジッドフレックス基板は、折り曲げたり、曲げたり、内部構造に巻き付けたりすることができます。航空電子機器モジュール、衛星サブシステム、ウェアラブルデバイスでは、いずれもリジッドフレックス基板を採用しており、平面PCBアセンブリでは実現できないほど、限られた筐体スペースに電子部品を凝縮しています。折り曲げ形状はPCB設計の一部として設計されており、ケーブルやブラケットで代用されることはありません。

3D fold geometry · mechanical integration · fits fixed enclosure volume
03

Mass and Volume Reduction — Measurable, Not Estimated

Removing connectors, redundant PCB substrate layers and inter-board cables typically reduces assembly mass by 30–70% and volume by 40–60% compared to an equivalent multi-board assembly. For aerospace and wearable applications, these reductions are primary design requirements — not convenience features.

30–70% mass reduction · 40–60% volume reduction · aerospace & wearable
技術仕様

リジッドフレックスPCBの完全な仕様

Design and fabrication under one roof — no design-to-fab handoff. Fold geometry, transition zone and layer stack reviewed together.

加工パラメータ

合計層数2 – 20 layers (rigid + flex)
フレックス領域レイヤー1 – 8 continuous flex layers
最小曲げ半径0.5 mm dynamic · 0.3 mm static
フレックス・カッパー・タイプフレックスゾーン用 圧延焼鈍(RA)
基材ポリイミドフレックスコア+FR4/高Tgリジッド

性能と基準

Via Typesリジッド領域におけるスルーホール + 埋込み/ブラインド
IPC構築基準Class 2 default · Class 3 on request
フレックス・サイクル評価Millions dynamic · 100+ static
表面仕上げENIG / ENEPIG / OSP
基板の厚さ(リジッド)0.4 mm – 3.2 mm
製造工程

リジッドフレックス基板の製造方法

The most complex standard PCB construction — combining multilayer rigid and flexible processes in a single assembly.

01
ステップ 01

フレックスコアの準備

フレックス領域の回路用に、RA銅を塗布したポリイミド基板にパターニングを施します。フレックス配線を保護するためにカバーレイを積層し、SMTパッドは露出させたままにします。

02
ステップ 02

リジッド・ビルドアップ積層

精密な多層プレス工程において、フレックスコアの剛性ゾーンの上に、FR4または高Tgプリプレグ層が積層されます。

03
ステップ 03

ドリリングおよびビア形成

Mechanical and laser drilling creates through-holes and blind vias. Only rigid zones receive blind vias — flex regions route continuously through all layers.

04
ステップ 04

仕上げ、テスト、および3D検証

ENIG仕上げ、100%の電子試験、および物理的な折り曲げ形状検証により、出荷前にアセンブリが意図された3D形状に適合していることが確認されます。

用途

リジッドフレックスがパッケージングの課題を解決する場面

ハーネスやコネクタで接続された複数のプリント基板(PCB)から構成される製品は、すべてリジッドフレックス化による簡素化の対象となります。

01

航空宇宙・航空電子機器

質量とコネクタの信頼性がミッション要件となる、折り畳み式の3Dアビオニクスモジュール。

02

医療用インプラント

身体の形状に適合する必要がある心臓用医療機器、人工内耳、および手術用カメラ向けのリジッドフレックス基板。

03

スマートウォッチ・ウェアラブル端末

Hinge-crossing rigid-flex replacing board-to-board connectors — reducing height and failure modes.

04

カメラ・内視鏡

ミラーレスカメラ、アクションカメラ、および3.5 mm内視鏡シャフトアセンブリにおける多軸回転。

05

UAVおよびドローンの電子機器

機体構造に組み込まれるフライトコントローラーボードにより、コネクタの数を減らし、質量を低減する。

06

軍事・防衛

固定シャーシの容積内に収まる、軍事用無線、誘導、および電子戦(EW)システム向けのコンフォーマルアセンブリ。

07

衛星

衛星の姿勢制御および展開型センサーアレイ向けに、質量を最適化したリジッド・フレックス基板。

08

産業用ロボット

協働ロボットアームおよび自律移動ロボットのセンサーアセンブリにおける関節横断屈曲。

製造・品質

Rigid-flex quality — verified at both rigid and flex disciplines.

Rigid-flex boards must satisfy both IPC-6012 (rigid) and IPC-6013 (flex) criteria simultaneously. Our transition zone microsection — included on every qualification lot — confirms the interface integrity that field reliability depends on.

  • IPC-6013リジッドフレックスPCBの認定基準
  • IPC-A-600 クラス 2 / 3許容基準
  • ISO 9001:2015第三者による監査を受けた品質管理
  • RoHS / REACHEUの有害物質規制への準拠

検査および試験方法

  • 100% Electrical Test — Flying Probeすべてのネット、すべてのボード
  • 100% AOI — All Layers自動光学検査
  • Flex Cycling — Bend ZoneIPC-TM-650 2.4.34「認定ロット」の規定に基づき
  • Microsection — Flex-to-Rigid Transition遷移領域の完全性検証
  • カバーレイの剥離強度IPC-TM-650 2.4.9 に基づき
  • X-Ray — Buried Via Registration剛性領域における層の位置合わせ
  • TDRインピーダンス±5% on controlled rigid-zone lines
  • 3D形状チェック認定ロットの物理的な折り目とフィット感
機能の例

当社が製造したリジッドフレックス基板

Real 3D packaging challenges — solved with rigid-flex.

Aerospace · Avionics

Folded Avionics Module — 12-Layer

3 rigid zones + 2 flex regions, IPC Class 3, polyimide, fitting a 55×35×12 mm enclosure for a flight data recorder.

12L
レイヤー
3剛性帯
構造
IPC 3
stdの構築
結果

DO-160の振動および熱特性認定試験に初回で合格した。3枚のPCBと2つのコネクタからなるアセンブリを交換した結果、質量を38%削減し、2つのコネクタに関する故障モードを排除した。

Medical · Endoscope

3.5 mm 内視鏡カメラ リジッド・フレックス

8-layer rigid-flex for a 3.5 mm scope — image sensor, LED driver and connection ribbon in one continuous assembly, biocompatible ENIG.

3.5mm
スコープ径
8L R-F
テクノロジー
ISO10993
生体適合性
結果

初回製造品の物理的適合性が直径3.5 mmで確認されました。EU指定機関は、初回審査において規制関連文書を承認しました。

Wearable · Smartwatch

Smartwatch — 0.55 mm Total Stack

6層リジッドフレックス、総厚0.55 mm、ヒンジ部での動的屈曲サイクル数200,000回、生体適合性ENIG、SoCゾーンに0.4 mm BGA。

0.55mm
合計の厚さ
20万
フレックスサイクル
99%
ファーストパス
結果

従来のコネクタ式設計に比べ、時計ケースの厚みを0.6 mm薄くしました。2年間の生産期間中、カバーレイの剥離は1件も発生しませんでした。

FAQ

リジッドフレックス基板に関するよくある質問

リジッド・フレックス回路の設計、製造、およびトランジションゾーンの設計に関する技術的な質問。

Traces in the flex region must run perpendicular to the bend axis — never parallel. Parallel traces in the bend zone experience pure tensile or compressive stress during bending and will fatigue and fracture. Perpendicular traces experience lateral stress, which the RA copper grain structure handles well. Our DFM review checks trace orientation in every flex region before fabrication begins.

In your Gerber/ODB++ package, include a separate layer defining the rigid and flex zones (typically called 'Flex Area' or 'Bend Region'). In your fabrication drawing, specify the bend axis, nominal bend radius, static vs dynamic flex classification, and stiffener requirements. Our DFM template provides a checklist — contact us for the latest version before starting your layout.

The flex region can have 1–8 continuous copper layers. Most wearable and medical rigid-flex designs use 2 or 4 flex layers. More layers in the flex region increase stiffness and require a larger minimum bend radius — our engineers calculate the required radius based on your copper weight and layer count during the DFM review.

Yes — blind and buried vias are available in the rigid zones. The flex region uses through-connections that continue as copper traces on the flex layers. Standard through-hole and blind/buried vias in rigid zones allow the same routing flexibility as a standard HDI rigid board. Microvias in rigid zones require additional press cycles and are quoted per design.

Dynamic flex regions are qualified to continuous bending through the specified bend radius over the specified number of cycles. We do not qualify fold angle directly — instead, the qualification is expressed as bend radius + cycle count. A 90° fold at 0.5 mm bend radius and 1 million cycles is a standard dynamic flex qualification. For other fold angles, the bend radius is the controlling parameter: smaller radius = higher stress = fewer cycles to failure.

Yes — for new rigid-flex designs, we offer a physical qualification unit fold verification service. The first-off board is folded to the nominal assembly geometry and photographed in the folded state. This confirms the board fits the intended enclosure before production quantities are released. Dimensional check reports are available on request.

お見積りをご依頼ください

Get your rigid-flex design reviewed — today.

組立図と回路図をお送りください。当社のリジッドフレックスエンジニアが、8時間以内にお客様の3D折り曲げ形状、遷移領域、および層構成を確認いたします。

  • すべてのお問い合わせにDFMレビューが含まれます
  • NDA signed on request — standard practice
  • 8営業時間以内にご返信いたします
  • 48時間でのプロトタイプ作成が可能
  • お見積もりのご依頼に、ご契約の義務は一切ありません
リジッドフレックス基板の見積もり依頼 All files encrypted · Max 80MB · DFM review included

お見積りのお申し込み

以下の詳細をご記入ください。折り返しご連絡いたします。

WhatsApp