Every single unit — not a sample — is visually inspected, dimensionally verified and cross-checked against a full history of test data before it's packaged and released. No board leaves without a documented pass.
上流工程のテストでは電気的な不具合が検出されます。最終検査では、それ以外のすべての不具合が発見されます。カーソルを合わせると詳細が表示されます。
IPC-A-610の基準に基づき、拡大鏡を用いてはんだ接合部の品質、トゥームストーニング、濡れ不良、フラックス残留物、およびシルクスクリーンの可読性を検査した。
ラベルの誤り、バーコードの不一致、リールまたはトレイあたりの数量の不一致などについて、封緘前に発注書(PO)および部品表(BOM)と照合して確認する。
出荷が許可される前に、適合証明書、材料証明書、または試験報告書のセットに不備がある場合は、その旨が指摘されます。
最終梱包の前に、緩んでいる、あるいは締め付けが不十分な金具、接続が不十分なコネクタ、欠落しているスタンドオフ、および機械的な嵌合の問題が発見された。
MSL認定部品は、所定の保管期間における曝露条件が適切であることを確認した後、乾燥剤および湿度インジケーターカードとともに防湿袋に密封されます。
Every unit's AOI, X-ray, ICT and functional test records are reconciled — any missing or inconsistent record halts the release.
梃子の反りやねじれ、厚さおよびアウトラインの寸法については、梱包の直前に図面の許容誤差に基づいて再確認を行う。
リビジョンマーク、日付コード、部品マークを照合し、古いリビジョンや混在したリビジョンが顧客に届くことを未然に防いでいます。
Final inspection is not a single check — it's the consolidation point where every prior test result, every visual pass and every packaging step comes together into one shipping decision.
Results from every upstream station — AOI, X-ray, ICT, flying probe and functional test — are pulled and reconciled against the unit or lot serial number before any physical inspection begins.
AOI · X-ray · ICT · flying probe · functional testEvery unit is inspected under magnification against IPC-A-610 Class 2/3 workmanship criteria — solder joint quality, component placement, silkscreen legibility and conformal coating coverage — along with board warpage, connector seating and standoff height.
IPC-A-610 · 10× magnification · 100% coverageラベルの内容、バーコード、数量は、発注書(PO)および部品表(BOM)と照合されます。各ユニットを袋詰め、箱詰め、またはリール巻きにする前に、ESD対策済みの梱包材が正しい部品に使用されているか確認されます。
ESD-safe packaging · label vs. PO/BOM audit湿気に敏感なアセンブリは、J-STD-033に準拠して、乾燥剤および湿度インジケーターカードを入れた防湿袋に密封されます。ESD包装は、引き渡し前にANSI/ESD S20.20に準拠して検証されます。
J-STD-033 · ANSI/ESD S20.20Test reports, certificates of conformance and material certifications are compiled into a single traceable document package for the shipment or lot — ready for customer incoming inspection.
CoC · test reports · material certs専任のOQA審査担当者が、出荷前に最終的な抜き取り検査を行い、承認の署名を行います。当該出荷分の欠陥の傾向および歩留まりデータは、継続的な改善のために生産技術部門にフィードバックされます。
OQA sign-off · yield & defect trend feedbackEvery criterion applied at final inspection is traceable to a written standard — not operator judgment.
Every board is inspected under magnification against IPC-A-610 Class 2 or Class 3 acceptance criteria — solder joint fillet quality, component placement and alignment, silkscreen legibility, and conformal coating coverage where specified.
ANSI/ESD S20.20に準拠し、全工程においてESD対策済みの梱包材を使用しています。湿気に敏感なデバイスは、J-STD-033に準拠して、乾燥剤および湿度インジケーターカードを入れた防湿袋に密封され、外装には適切な保存期間の表示が記載されています。
Every shipment ships with a bundled document package: certificate of conformance, all upstream test reports, material and RoHS/REACH certifications, and lot-level traceability records — organized per shipment or lot so your incoming inspection team can verify in minutes.
以下の各パラメータは、当社の製造最終検査ラインにおける数値を反映したものです。すべての注文には、完全な検査記録およびOQAの承認書類が同梱されます。
| パラメータ | 最終検査仕様書 | ステータス |
|---|---|---|
| 検査範囲 | 100% — every unit, no AQL sampling | 在庫あり |
| 施工基準 | IPC-A-610 クラス2/クラス3 | 在庫あり |
| 倍率 | 10× – 40× under lit inspection stations | 在庫あり |
| 1日あたりの検査台数 | 最大15,000台 | 在庫あり |
| ドキュメントの処理期間 | 最終承認から24時間後 | 在庫あり |
| パッケージの選択肢 | ESDトレイ/テープ&リール/乾燥剤入りMBB | 在庫あり |
| MSLハンドリング | J-STD-033準拠の湿度インジケーターカード | 在庫あり |
| ESD準拠 | ANSI/ESD S20.20 プログラム | 在庫あり |
| 欠陥漏れ率 | < 50 ppm の目標値 | 在庫あり |
最終検査は、当社の品質管理システム全体が結集する場です。当社が保有するすべての認証および上流工程のあらゆる試験方法は、製品が出荷される前にOQAによる承認に反映されます。
実際の欠陥は、顧客に届く前に最終検査で発見され、出荷が中止されました。
自動車業界のティア1サプライヤーのロットにおいて、出荷品が倉庫を出荷される前の最終検査におけるPO/BOM照合の過程で、梱包ラベルの不一致が指摘されました。
出荷前に不一致を発見し、24時間以内にロット全体のラベルを貼り替え、再確認を行いました。顧客には誤ってラベルが貼られた製品が渡されることはありませんでした。
最終検査では、クラスII医療機器プログラム向けに専用のMSL保存期間チェックを追加し、J-STD-033に準拠してすべてのリールを密封するとともに、湿度インジケーターによる検証を行いました。
このプログラムは、湿気に敏感な取り扱いに関する指摘事項がゼロという結果で顧客の品質監査に合格し、文書化されたMSLプロセスが業界最高水準であると評価されました。
ある重工業用組立品において繰り返し発生していた輸送中の損傷に関するクレームは、返品された製品の最終検査の際、緩衝材が不十分であったことが原因であることが判明した。
新しい梱包仕様が、標準的なOQAチェックリストに組み込まれた。その結果、その後の2四半期で輸送中の破損によるクレームが85%減少した。
A final inspection stamp is only as good as the process behind it. Ours combines 100% unit coverage, documented standards and a dedicated audit gate — not a rubber stamp on a sampling plan.
We don't rely on AQL sampling at final inspection. Every single board is visually and dimensionally checked before packaging — the only way to guarantee zero surprises at your incoming dock.
Certificates of conformance, test reports and material certifications are bundled and delivered within 24 hours of release — ready for your own incoming inspection team.
当社は、欠陥見逃し率を正式なKPIとして追跡し、発見されたすべての事項を生産エンジニアリング部門にフィードバックすることで、出荷ごとにその数値を低減させています。
Final release requires sign-off from a quality reviewer independent of the production line — an extra layer of accountability standard on every order, at no added cost.
最終検査および出荷前100%品質管理に関するよくある質問。
AOI, X-ray, ICT and flying probe each verify one specific aspect of a board — placement, solder joints, or electrical continuity — at a single point in the process. Final inspection happens last and covers everything those methods don't: cosmetic workmanship, packaging accuracy, documentation completeness, MSL/ESD compliance, and a review that every prior test record is present and passing. It's the consolidation step, not a replacement for upstream testing.
100% — every unit, not a statistical AQL sample. Each board is visually and dimensionally inspected under magnification, and its full test data history is reconciled before it's cleared for packaging. Sampling plans are appropriate for some incoming material checks, but not for outgoing quality control on finished assemblies.
はい。すべての出荷には、適合証明書に加え、まとめられた試験報告書一式、材料証明書、およびロットレベルのトレーサビリティに関する書類が同梱されています。これらの書類一式はまとめてまとめられ、最終リリースから24時間以内に納品されます。
MSL指定のアセンブリは、J-STD-033に準拠して、乾燥剤および湿度インジケーターカードを同梱した防湿袋に密封されており、外装には保存期間およびMSLレベルが明記されています。また、静電気に敏感な部品を搭載した基板については、すべての梱包材がANSI/ESD S20.20に準拠したESD対策が施されています。
The affected unit or lot is held and does not receive OQA sign-off. Depending on the finding, it's routed to rework, re-test, or scrap, and the root cause is logged and fed back to production engineering as part of our defect trend reporting — so the same issue is less likely to recur on the next run.
Yes. We regularly align our final inspection checklist and documentation package to match a customer's own incoming quality requirements — including specific IPC class, additional dimensional checks, or extra certificates — so your receiving team can clear shipments faster.
Tell us about your assembly and quality requirements — our quality team will confirm the final inspection and documentation scope along with your quote.
以下の詳細をご記入ください。折り返しご連絡いたします。