最小発注数量1個からの短納期プロトタイプおよびNPI組立、DFM/DFAに関する技術的フィードバックを提供し、 設計の検証が完了次第、量産へ直接移行可能です。
最初の概念実証から量産前の検証に至るまで、各業界をどのように支援しているか、カーソルを合わせると詳細が表示されます。
費用のかかるIATF 16949準拠の量産用金型製作に先立ち、DFMフィードバックを反映したECUおよびセンサーのプロトタイプを迅速に製作します。
デバイススタートアップ企業向けの初期設計検証テストを支援するための、初回製品検査および文書化された製造プロセス。
本格的な量産用金型の導入に先立ち、制御・自動化ハードウェアの小ロット試作を行う。
コンポーネントのフルリール発注を待つことなく、クラウドファンディング用デモ機、EVT、DVTの各ビルド間で迅速に再試作を繰り返すことができます。
インフラ規模での調達に先立ち、アンテナおよび信号経路の設計を検証するための、短納期のRFモジュール試作品。
NDAに基づくエンジニアリング評価用ユニットの、初回試作品の構築記録および迅速な再製造のサポート。
ファームウェアとハードウェアを並行してスプリント形式で改良を繰り返す、コネクテッドデバイス分野のスタートアップ企業向けの、1個からの最小発注数量(MOQ)対応アセンブリ。
量産に先立ち、熱特性およびレイアウト性能を検証するための、短納期の電力変換器プロトタイプ。
プロトタイプの完成を待つ1時間ごとに、製品の発売は1時間ずつ遅れてしまいます。当社のプロセスは、そのスケジュールを短縮するように構築されています。
Upload Gerbers and BOM for an instant online quote. Engineering and BOM review begins immediately — no waiting on a sales cycle to get a project moving.
Instant quote · 1-piece MOQ当社のエンジニアが、4営業時間以内にフットプリント、パネル化、部品の入手可能性、および組立の実現可能性を確認し、お客様が製造を決定する前に問題点を指摘いたします。
4h turnaround · free of chargeBoards move onto expedited fabrication lines while we source components in prototype quantities — including small-reel and cut-tape purchasing, so you're never forced to buy a full reel for a single build.
expedited fab · cut-tape sourcingSMT/THT assembly is followed by a documented first-article inspection report, then same-day shipping. Need a re-spin? We rebuild within 24–48 hours using the same DFM data — and scale directly to production once your design is validated.
FAI included · 24–48h re-spin · bridge to productionPrototype builds get the same engineering attention as production — just faster.
Our engineers review every prototype submission for manufacturability and assembly feasibility — footprint accuracy, component orientation, panelization and stack-up — with comments returned within 4 working hours, free of charge.
Prototype quantities don't require full-reel purchasing. We source in small-reel and cut-tape formats where available, and flag any part with a minimum-buy conflict during the DFM stage — before it becomes a surprise cost.
専用の試作組立ラインでは、通常は量産ロットの後に順番待ちとなる基板について、ファインピッチSMT実装および手作業によるTHTはんだ付けを行っています。標準的な納期は72時間ですが、緊急の案件には24時間のエクスプレスオプションもご利用いただけます。
Once your design is validated, we carry the same DFM data, approved BOM and process notes directly into a production quote — no re-review, no re-sourcing from scratch, and no need to switch suppliers between prototype and volume manufacturing.
Every parameter below applies from your very first prototype run — the same process controls carry through when you scale to production.
| パラメータ | 試作能力 | ステータス |
|---|---|---|
| 最小注文数量 | 1個 | 在庫あり |
| 最短納期 | 24時間(エクスプレス)/72時間(標準) | 在庫あり |
| ボードサイズの範囲 | 10mm × 10mm – 500mm × 500mm | 在庫あり |
| 層数の範囲 | 1 – 20 layers | 在庫あり |
| 部品調達リードタイムの短縮 | Same-day – 3 business days on common parts | 在庫あり |
| 小型リール/カットテープの調達 | Available — no full-reel purchase required | 在庫あり |
| BOM/ガーバーデータのレビュー所要時間 | 4営業時間以内 | 在庫あり |
| 組立技術 | SMT、THT、混合、ファインピッチの手はんだ付け | 在庫あり |
| 初回製品検査 | すべての試作機に含まれています | 在庫あり |
| 再スピン/反復処理のサポート | Rush rebuild within 24 – 48 hours | 在庫あり |
| ブリッジ・トゥ・プロダクション | 直接的なスケールアップ経路、DFMデータの引き継ぎ | 在庫あり |
Every prototype — even a single unit — is built under the same quality system as our production runs, with a documented first-article inspection report shipped alongside your board.
Real fast-turn builds — from first spin to production handoff.
あるウェアラブルデバイス開発のスタートアップ企業は、臨床試験の締め切りに間に合わせるため、センサーの配置を確定させるまでに3回の基板設計変更を必要としましたが、各試作は24時間以内に完成しました。
最終設計が確定し、臨床試験用ユニットも予定通りに納入されました。顧客側のチームは、迅速な再設計サイクルのおかげで、以前のサプライヤーと比較して約6週間の短縮につながったと評価しています。
当社のDFMレビューにより、組み立て開始前にBLEモジュールのフットプリントの不一致が指摘され、立ち上げ間もないIoTハードウェアチームの無駄な製造サイクルを回避することができました。
部品の発注前にフットプリントの修正が完了したため、推定で5日間の工数と、廃棄となった部品の発注コストを節約できた。
あるロボット工学のスタートアップ企業は、4回の試作を経てモーターコントローラーの設計を検証した後、同じサプライヤーを通じて直接5,000台の量産に移行した。
Production quote turned around in 24 hours using the validated BOM and DFM data — no re-review cycle and no supplier switch required to scale.
Early-stage development is defined by speed and iteration. Our process is built around both — without cutting corners on quality when it's time to scale.
専用の試作ラインと24時間対応の迅速な組立オプションにより、今日設計変更を行えば、明日にはお客様の作業台で動作する基板を手に入れることができます。
パネルの最低発注数量や、リール単位での部品購入の義務はありません。当社は完全な「1ピース」での製造に対応しているため、創業間もないチームが生産を正当化するために過剰発注を強いられることはありません。
Every submission gets a genuine DFM/DFA review from our engineering team — not just an automated rules check — with feedback returned in hours, not days.
No re-qualification, no re-sourcing and no re-DFM when you're ready to scale — your validated design and BOM data move straight into a production quote.
試作および新製品導入(NPI)の組立、納期、量産へのスケールアップに関するよくある質問。
当社のエクスプレスオプションでは、一般的なスルーホールおよびSMT基板について、承認済みのガーバーデータ/BOMおよび入手可能な部品在庫から基板の出荷まで24時間でお届けします。標準的な試作リードタイムは72時間です。特殊なラミネート材を使用する基板や、調達リードタイムが長い部品を使用する基板については、個別に見積もりを提示いたします。
いいえ。組み立て済みのユニット1台からでもご注文を承っております。パネルの最低注文数といった制限はなく、現段階ではプロジェクトで実際に必要な枚数以上の基板をご注文いただく必要もありません。
はい。メーカーや販売代理店が対応している限り、当社は小型リールやカットテープ形式での調達を行っています。そのため、1回限りの組み立てのために3,000個入りのリール1本丸ごとを購入する必要はありません。部品がリール単位でのみ入手可能な場合は、DFM/BOMレビューの際にその旨を明記しますので、予期せぬ事態は発生しません。
Re-spins are treated as priority builds. Submit your updated Gerbers/BOM referencing the original order, and we'll turn the rebuild around in 24–48 hours. Our engineers also compare the new revision against your previous DFM notes to confirm earlier issues were resolved.
はい、すべての試作機には、追加料金なしで初回品検査報告書が添付されます。この報告書には、寸法検査、BOMに基づく部品配置の確認、およびAOI検査の結果が記載されており、設計検証試験や投資家・顧客へのプレゼンテーションを裏付ける書面記録としてご利用いただけます。
Yes — this is a core part of our service. Once your design is validated, we carry your approved DFM data, BOM and process notes directly into a production quote, typically returned within 24 hours, with no need to re-qualify the design or switch suppliers.
Upload your files and our engineering team will return a free DFM/DFA review and quote within 4 working hours — with same-day scheduling available for urgent projects.
以下の詳細をご記入ください。折り返しご連絡いたします。
当サイトでは、ユーザーの利便性を高めるためにクッキーを使用しています。詳しくは、当社の プライバシーポリシー.