Fast-turn prototype and NPI assembly with 1-piece minimum order, engineering DFM/DFA feedback and a direct bridge to mass production once your design is validated.
From first proof-of-concept to pre-production validation, hover to see how we support each industry.
Rapid ECU and sensor prototype builds with DFM feedback ahead of costly IATF 16949 production tooling.
First-article inspection and documented builds to support early design-verification testing for device startups.
Low-volume pilot runs for control and automation hardware before committing to full production tooling.
Rapid re-spins between crowdfunding demo, EVT and DVT builds without waiting on full-reel component orders.
Fast-turn RF module prototypes to validate antenna and signal-chain designs before infrastructure-scale sourcing.
Documented first-article builds and rapid re-spin support for engineering evaluation units under NDA.
1-piece MOQ assembly for connected-device startups iterating firmware and hardware in parallel sprints.
Quick-turn power-converter prototypes to validate thermal and layout performance before a production run.
Every hour spent waiting on a prototype is an hour your product launch slips. Our process is built to compress that timeline.
Upload Gerbers and BOM for an instant online quote. Engineering and BOM review begins immediately — no waiting on a sales cycle to get a project moving.
Instant quote · 1-piece MOQOur engineers check footprints, panelization, part availability and assembly feasibility within 4 working hours, flagging issues before you commit to a build.
4h turnaround · free of chargeBoards move onto expedited fabrication lines while we source components in prototype quantities — including small-reel and cut-tape purchasing, so you're never forced to buy a full reel for a single build.
expedited fab · cut-tape sourcingSMT/THT assembly is followed by a documented first-article inspection report, then same-day shipping. Need a re-spin? We rebuild within 24–48 hours using the same DFM data — and scale directly to production once your design is validated.
FAI included · 24–48h re-spin · bridge to productionPrototype builds get the same engineering attention as production — just faster.
Our engineers review every prototype submission for manufacturability and assembly feasibility — footprint accuracy, component orientation, panelization and stack-up — with comments returned within 4 working hours, free of charge.
Prototype quantities don't require full-reel purchasing. We source in small-reel and cut-tape formats where available, and flag any part with a minimum-buy conflict during the DFM stage — before it becomes a surprise cost.
Dedicated prototype assembly lines handle fine-pitch SMT placement and hand-soldered THT for boards that would otherwise queue behind production runs. Standard turnaround is 72 hours; a 24-hour express option is available for urgent builds.
Once your design is validated, we carry the same DFM data, approved BOM and process notes directly into a production quote — no re-review, no re-sourcing from scratch, and no need to switch suppliers between prototype and volume manufacturing.
Every parameter below applies from your very first prototype run — the same process controls carry through when you scale to production.
| Параметр | Prototype Capability | Статус |
|---|---|---|
| Minimum Order Quantity | 1 piece | Доступно |
| Fastest Turnaround | 24 hours (express) / 72 hours (standard) | Доступно |
| Диапазон размеров досок | 10mm × 10mm – 500mm × 500mm | Доступно |
| Layer Count Range | 1 – 20 layers | Доступно |
| Component Sourcing Turnaround | Same-day – 3 business days on common parts | Доступно |
| Small-Reel / Cut-Tape Sourcing | Available — no full-reel purchase required | Доступно |
| BOM / Gerber Review Turnaround | Within 4 working hours | Доступно |
| Assembly Technology | SMT, THT, mixed, fine-pitch hand-solder | Доступно |
| First Article Inspection | Included on every prototype build | Доступно |
| Re-spin / Iteration Support | Rush rebuild within 24 – 48 hours | Доступно |
| Bridge-to-Production | Direct scale-up path, DFM data carried forward | Доступно |
Every prototype — even a single unit — is built under the same quality system as our production runs, with a documented first-article inspection report shipped alongside your board.
Real fast-turn builds — from first spin to production handoff.
A wearable-device startup needed three board re-spins to finalize sensor placement ahead of a clinical trial deadline, each build turned in 24 hours.
Final design locked and clinical trial units delivered on schedule. The customer's team credited the fast re-spin loop with saving roughly six weeks versus their previous supplier.
Our DFM review flagged a footprint mismatch on a BLE module before assembly began, avoiding a wasted build cycle for an early-stage IoT hardware team.
Corrected footprint resolved before parts were ordered, saving an estimated 5 days and the cost of a scrapped component order.
A robotics startup validated their motor-controller design through four prototype spins, then scaled directly to a 5,000-unit production run with the same supplier.
Production quote turned around in 24 hours using the validated BOM and DFM data — no re-review cycle and no supplier switch required to scale.
Early-stage development is defined by speed and iteration. Our process is built around both — without cutting corners on quality when it's time to scale.
Dedicated prototype lines and an express 24-hour assembly option mean a design change today can be a working board on your bench tomorrow.
No panel minimums, no full-reel component purchases. We support true 1-piece builds so early-stage teams aren't forced to over-order to justify a run.
Every submission gets a genuine DFM/DFA review from our engineering team — not just an automated rules check — with feedback returned in hours, not days.
No re-qualification, no re-sourcing and no re-DFM when you're ready to scale — your validated design and BOM data move straight into a production quote.
Common questions about prototype and NPI assembly, turnaround times and scaling to production.
Our express option is 24 hours from approved Gerbers/BOM and available component stock to shipped board, for common through-hole and SMT builds. Standard prototype turnaround is 72 hours. Boards using speciality laminates or components with longer sourcing lead times are quoted individually.
No. We accept orders as small as a single assembled unit. There's no panel minimum and no requirement to order more boards than your project actually needs at this stage.
Yes. We source in small-reel and cut-tape formats wherever the manufacturer or distributor supports it, so you don't need to buy a full reel of 3,000 parts for a one-off build. Where a part is only available in full-reel quantity, we'll flag it during the DFM/BOM review so there are no surprises.
Re-spins are treated as priority builds. Submit your updated Gerbers/BOM referencing the original order, and we'll turn the rebuild around in 24–48 hours. Our engineers also compare the new revision against your previous DFM notes to confirm earlier issues were resolved.
Yes, a first-article inspection report is included with every prototype build at no extra charge. It documents dimensional checks, component placement verification against your BOM, and AOI results, giving you a written record to support design-verification testing or investor/customer reviews.
Yes — this is a core part of our service. Once your design is validated, we carry your approved DFM data, BOM and process notes directly into a production quote, typically returned within 24 hours, with no need to re-qualify the design or switch suppliers.
Upload your files and our engineering team will return a free DFM/DFA review and quote within 4 working hours — with same-day scheduling available for urgent projects.
Введите данные ниже, и мы свяжемся с вами в ближайшее время.